It also stores the dirty status so that's known.
This does some Makefile tricks so that we only rebuild when the git
hash changes. This avoids rebuilding the world every time we run
make.
Also adds fusesoc generator, so that should continue to work as
before.
Signed-off-by: Dan Horák <dan@danny.cz>
Signed-off-by: Michael Neuling <mikey@neuling.org>
This expands the field in the log buffer that stores the instruction
fetched from the icache to 36 bits, so that we get the insn_code and
illegal instruction indication. To do this, we reclaim 3 unused bits
from execute1's portion and one other unused bit (previously just set
to 0 in core.vhdl).
This also alters the trigger behaviour to stop after one quarter of
the log buffer has been filled with samples after the trigger, or 256
entries, whichever is less. This is to ensure that the trigger event
doesn't get overwritten when the log buffer is small.
This updates fmt_log to the new log format. Valid instructions are
printed as a decimal insn_code value followed by the bottom 26 bits of
the instruction. Illegal instructions are printed as "ill" followed
by the full 32 bits of the instruction.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Do more decoding of the instruction ahead of the IDLE state
processing so that the IDLE state code becomes much simpler.
To make the decoding easier, we now use four insn_type_t codes for
floating-point operations rather than two. This also rearranges the
insn_type_t values a little to get the 4 FP opcode values to differ
only in the bottom 2 bits, and put OP_DIV, OP_DIVE and OP_MOD next to
them.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This provides access to the SPRs via the JTAG DMI interface. For now
they are still accessed as if they were GPR/FPRs using the same
numbering as before (GPRs at 0 - 0x1f, SPRs at 0x20 - 0x2d, FPRs at
0x40 - 0x5f).
For XER, debug reads now report the full value, not just the bits that
were previously stored in the register file. The "slow" SPR mux is
not used for debug reads.
Decode2 determines on each cycle whether a debug SPR access will
happen next cycle, based on whether there is a request and whether the
current instruction accesses the SPR RAM.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Besides the overflow and status carry bits, XER has 18 bits which need
to retain the value written by mtxer (in case software wants to
emulate the move-assist instructions (lswi, lswx, stswi, stswx).
Until now these bits (and others) have been stored in the GPR file as
a "fast" SPR, but this causes complications because XER is not really
a fast SPR.
Instead, we now store these 18 bits in the 'ctrl' signal, which exists
in execute1. This will enable us to simplify the data path in future,
and has the added bonus that with a little bit of plumbing, we can get
the full XER value printed when dumping registers at the end of a
simulation.
Therefore this changes scripts/run_test.sh to remove the greps which
exclude XER from the comparison of actual and expected register
results.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Revert to linking dynamically by default, can statically link with
`make STATIC_URJTAG=1`
Fixes#351
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
"-b ecp5" will select ECP5 interface that talks to a JTAGG
primitive.
For example with a FT232H JTAG board:
./mw_debug -t 'ft2232 vid=0x0403 pid=0x6014' -s 30000000 -b ecp5 mr ff003888 6
Connected to libftdi driver.
Found device ID: 0x41113043
00000000ff003888: 6d6f636c65570a0a ..Welcom
00000000ff003890: 63694d206f742065 e to Mic
00000000ff003898: 2120747461776f72 rowatt !
00000000ff0038a0: 0000000000000a0a ........
00000000ff0038a8: 67697320636f5320 Soc sig
00000000ff0038b0: 203a65727574616e nature:
Core: running
NIA: c0000000000187f8
MSR: 9000000000001033
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
liburjtag isn't in Debian, so usually we're pointing at a urjtag
build directory when building mw_debug
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
This makes it simpler to work out when to deliver a FPU unavailable
interrupt. This also means we can get rid of the OP_FPLOAD and
OP_FPSTORE insn_type values.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This compares the address being fetched with the contents of a
register that can be set via DMI, and if they match, stops the
logging. Since this works on the address being fetched rather than
executed, it is subject to false positives.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds the skeleton of a floating-point unit and implements the
mffs and mtfsf instructions.
Execute1 sends FP instructions to the FPU and receives busy,
exception, FP interrupt and illegal interrupt signals from it.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This extends the register file so it can hold FPR values, and
implements the FP loads and stores that do not require conversion
between single and double precision.
We now have the FP, FE0 and FE1 bits in MSR. FP loads and stores
cause a FP unavailable interrupt if MSR[FP] = 0.
The FPU facilities are optional and their presence is controlled by
the HAS_FPU generic passed down from the top-level board file. It
defaults to true for all except the A7-35 boards.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
To avoid adding too much logic, this moves the adder used by OP_ADD
out of the case statement in execute1.vhdl so that the result can
be used by OP_ADDG6S as well.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
These instructions use major opcode 4 and have a third GPR input
operand, so we need a decode table for major opcode 4 and some
plumbing to get the RC register operand read.
The multiply-add instructions use the same insn_type_t values as the
regular multiply instructions, and we distinguish in execute1 by
looking at the major opcode. This turns out to be convenient because
we don't have to add any cases in the code that handles the output of
the multiplier, and it frees up some insn_type_t values.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This also removes OP_MCRXR, as the mcrxr instruction was removed in
version 3.0B of the Power ISA, having been phased-out for the server
architecture since v2.02.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This logs 256 bits of data per cycle to a ring buffer in BRAM. The
data collected can be read out through 2 new SPRs or through the
debug interface.
The new SPRs are LOG_ADDR (724) and LOG_DATA (725). LOG_ADDR contains
the buffer write pointer in the upper 32 bits (in units of entries,
i.e. 32 bytes) and the read pointer in the lower 32 bits (in units of
doublewords, i.e. 8 bytes). Reading LOG_DATA gives the doubleword
from the buffer at the read pointer and increments the read pointer.
Setting bit 31 of LOG_ADDR inhibits the trace log system from writing
to the log buffer, so the contents are stable and can be read.
There are two new debug addresses which function similarly to the
LOG_ADDR and LOG_DATA SPRs. The log is frozen while either or both of
the LOG_ADDR SPR bit 31 or the debug LOG_ADDR register bit 31 are set.
The buffer defaults to 2048 entries, i.e. 64kB. The size is set by
the LOG_LENGTH generic on the core_debug module. Software can
determine the length of the buffer because the length is ORed into the
buffer write pointer in the upper 32 bits of LOG_ADDR. Hence the
length of the buffer can be calculated as 1 << (31 - clz(LOG_ADDR)).
There is a program to format the log entries in a somewhat readable
fashion in scripts/fmt_log/fmt_log.c. The log_entry struct in that
file describes the layout of the bits in the log entries.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This outputs a carriage return rather than a newline after the
display of the progress count during the load and save operations.
This makes the output more compact and better looking.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This describes how to build the tool on Fedora, and on Debian which lacks a packaged
liburjtag as of mid 2020.
Signed-off-by: Joel Stanley <joel@jms.id.au>
CFLAGS was defined but not used anywhere. This adds them to the compile
line, and fixes the warnings (and errors!) that result.
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds a "gpr" command for reading 1 or more GPRs/fast SPRs,
and a "mw" command for writing an 8-byte value to memory. It also
adds an "icreset" command for resetting the instruction cache
and fixes the "creset" command to actually reset the core instead
of starting it. The MSR is now printed along with the NIA in the
status information.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This comes in two parts:
- A generator script which uses LiteX to generate litedram cores
along with their init files for various boards (currently Arty and
Nexys-video). This comes with configs for arty and nexys_video.
- A fusesoc "generator" which uses pre-generated litedram cores
The generation process is manual on purpose. This include pre-generated
cores for the two above boards.
This is done so that one doesn't have to install LiteX to build
microwatt. In addition, the generator script or wrapper vhdl tend to
break when LiteX changes significantly which happens.
This is still rather standalone and hasn't been plumbed into the SoC
or the FPGA toplevel files yet.
At this point LiteDRAM self-initializes using a built-in VexRiscv
"Minimum" core obtained from LiteX and included in this commit. There
is some plumbing to generate and cores that are initialized by Microwatt
directly but this isn't working yet and so isn't enabled yet.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds test cases for:
- sc, illegals and decrementer exceptions
- decrementer overflow
- rfid
- mt/mf sprg0/1 srr0/1
- mtdec
- mtmsrd
- sc
It also adds these test cases to make check/check_light
Signed-off-by: Michael Neuling <mikey@neuling.org>
dependencies.py was pretty terrible at actually determining
dependencies. This improves it and also adds a --synth option.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
The current version of micropython in tests/micropython.bin is ancient.
Bug #135 points out that more recent versions are much smaller and they
also handle restart when ctrl+D is pressed.
Save all three versions of the file (elf, bin and hex) in micropython/
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Right now our test cases fold the SPRs into the GPRs. That makes
debugging fails more difficult than it needs to be, so print
out the CTR, LR and CR.
We still need to print the XER, but that is in two spots in microwatt
and will take some more work.
This also adds many instructions to the tests that we have added
lately including overflow instructions, CR logicals and mt/mfxer.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
This replaces the simple_ram_behavioural and mw_soc_memory modules
with a common wishbone_bram_wrapper.vhdl that interfaces the
pipelined WB with a lower-level RAM module, along with an FPGA
and a sim variants of the latter.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The icache_test.bin file was missing. This adds it (along with a python3
script to generate it).
We also add better reporting on errors
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This works with both the sim socket and urjtag, and supports the
new core functions, loading a file in memory etc...
The code still needs a lot of cleanup and a help!
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a debug module off the DMI (debug) bus which can act as a
wishbone master to generate read and write cycles.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dan Horák
Paul Mackerras
Michael Neuling