This adds the skeleton of a floating-point unit and implements the
mffs and mtfsf instructions.
Execute1 sends FP instructions to the FPU and receives busy,
exception, FP interrupt and illegal interrupt signals from it.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This extends the register file so it can hold FPR values, and
implements the FP loads and stores that do not require conversion
between single and double precision.
We now have the FP, FE0 and FE1 bits in MSR. FP loads and stores
cause a FP unavailable interrupt if MSR[FP] = 0.
The FPU facilities are optional and their presence is controlled by
the HAS_FPU generic passed down from the top-level board file. It
defaults to true for all except the A7-35 boards.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This is a NiteFury based PCIe M2 form-factor board originally
used for mining. It contains a speed grade 2 Artix 7 200T,
1GB of DDR3 and 32MB of flash.
The serial port is routed to pin 2 (RX) and 3 (TX) of the P2
connector (pin 1 is GND).
Note: Only 16MB of flash is currently usable until code is added
to configure the flash controller to use 4-bytes address commands
on that part.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a true random number generator for the Xilinx FPGAs which
uses a set of chaotic ring oscillators to generate random bits and
then passes them through a Linear Hybrid Cellular Automaton (LHCA) to
remove bias, as described in "High Speed True Random Number Generators
in Xilinx FPGAs" by Catalin Baetoniu of Xilinx Inc., in:
https://pdfs.semanticscholar.org/83ac/9e9c1bb3dad5180654984604c8d5d8137412.pdf
This requires adding a .xdc file to tell vivado that the combinatorial
loops that form the ring oscillators are intentional. The same
code should work on other FPGAs as well if their tools can be told to
accept the combinatorial loops.
For simulation, the random.vhdl module gets compiled in, which uses
the pseudorand() function to generate random numbers.
Synthesis using yosys uses nonrandom.vhdl, which always signals an
error, causing darn to return 0xffff_ffff_ffff_ffff.
This adds an implementation of the darn instruction. Darn can return
either raw or conditioned random numbers. On Xilinx FPGAs, reading a
raw random number gives the output of the ring oscillators, and
reading a conditioned random number gives the output of the LHCA.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This fixes up a few issues with parameters:
Only arty has "has_uart1" since we haven't added plumbing for a second UART
anywhere else. Also "uart_is_16550" was mixing on one of the nexys_video
targets, and nexys_video toplevel was missing LOG_LENGTH.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This imports via fusesoc a 16550 compatible (ie "standard") UART,
and wires it up optionally in the SoC instead of the potato one.
This also adds support for a second UART (which is always a
16550) to Arty, wired to JC "bottom" port.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At present this just has the Xilinx-specific multiplier code, but
might in future have other things.
This also adds the xilinx_specific fileset to the synth target.
Without that it was failing because there was no multiplier.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This plumbs the LOG_LENGTH parameter (which controls how many entries
the core log RAM has) up to the top level so that it can be set on
the fusesoc command line and have different default values on
different FPGAs.
It now defaults to 512 entries generally and on the Artix-7 35 parts,
and 2048 on the larger Artix-7 FPGAs. It can be set to 0 if desired.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a custom implementation of the multiplier which uses 16
DSP48E1 slices to do a 64x64 bit multiplication in 2 cycles.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The fetch2 stage existed primarily to provide a stash buffer for the
output of icache when a stall occurred. However, we can get the same
effect -- of having the input to decode1 stay unchanged on a stall
cycle -- by using the read enable of the BRAMs in icache, and by
adding logic to keep the outputs unchanged on a clock cycle when
stall_in = 1. This reduces branch and interrupt latency by one
cycle.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds an SPI flash controller which supports direct
memory-mapped access to the flash along with a manual
mode to send commands.
The direct mode can be set via generic to default to single
wire or quad mode. The controller supports normal, dual and quad
accesses with configurable commands, clock divider, dummy clocks
etc...
The SPI clock can be an even divider of sys_clk starting at 2
(so max 50Mhz with our typical Arty designs).
A flash offset is carried via generics to syscon to tell SW about
which portion of the flash is reserved for the FPGA bitfile. There
is currently no plumbing to make the CPU reset past that address (TBD).
Note: Operating at 50Mhz has proven unreliable without adding some
delay to the sampling of the input data. I'm working in improving
this, in the meantime, I'm leaving the default set at 25 Mhz.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a cache between the wishbone and litedram with the following
features (at this point, it's still evolving)
- 128 bytes line width in order to have a reasonable amount of
litedram pipelining on the 128-bit wide data port.
- Configurable geometry otherwise
- Stores are acked immediately on wishbone whether hit or miss
(minus a 2 cycles delay if there's a previous load response in the
way) and sent to LiteDRAM via 8 entries (configurable) store queue
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds an option to disable the main BRAM and instead copy a
payload stashed along with the init code in the secondary BRAM
into DRAM and boot from there
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These provides some info about the SoC (though it's still somewhat
incomplete and needs more work, see comments).
There's also a control register for selecting DRAM vs. BRAM at 0
(and for soft-resetting the SoC but that isn't wired up yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The old toplevel.vhdl becomes top-generic.vhdl, which is to be used
by platforms that do not have a litedram option.
Arty has its own top-arty.vhdl which supports litedram and is now
hooked up
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a new module to implement an MMU. At the moment it doesn't
do very much. Tlbie instructions now get sent by loadstore1 to mmu,
which sends them to dcache, rather than loadstore1 sending them
directly to dcache. TLB misses from dcache now get sent by loadstore1
to mmu, which currently just returns an error. Loadstore1 then
generates a DSI in response to the error return from mmu.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This comes in two parts:
- A generator script which uses LiteX to generate litedram cores
along with their init files for various boards (currently Arty and
Nexys-video). This comes with configs for arty and nexys_video.
- A fusesoc "generator" which uses pre-generated litedram cores
The generation process is manual on purpose. This include pre-generated
cores for the two above boards.
This is done so that one doesn't have to install LiteX to build
microwatt. In addition, the generator script or wrapper vhdl tend to
break when LiteX changes significantly which happens.
This is still rather standalone and hasn't been plumbed into the SoC
or the FPGA toplevel files yet.
At this point LiteDRAM self-initializes using a built-in VexRiscv
"Minimum" core obtained from LiteX and included in this commit. There
is some plumbing to generate and cores that are initialized by Microwatt
directly but this isn't working yet and so isn't enabled yet.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LiteDRAM at the moment pretty much enforces 100Mhz, and our software
isn't quite yet adaptable, so switch out default to 100Mhz accross
the board. Recent timing improvements should make it a non-issue.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This replaces the simple_ram_behavioural and mw_soc_memory modules
with a common wishbone_bram_wrapper.vhdl that interfaces the
pipelined WB with a lower-level RAM module, along with an FPGA
and a sim variants of the latter.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Vivado by default tries to flatten the module hierarchy to improve
placement and timing. However this makes debugging timing issues
really hard as the net names in the timing report can be pretty
bogus.
This adds a generic that can be used to control attributes to stop
vivado from flattening the main core components. The resulting design
will have worst timing overall but it will be easier to understand
what the worst timing path are and address them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This replaces loadstore2 with a dcache
The dcache unit is losely based on the icache one (same basic cache
layout), but has some significant logic additions to deal with stores,
loads with update, non-cachable accesses and other differences due to
operating in the execution part of the pipeline rather than the fetch
part.
The cache is store-through, though a hit with an existing line will
update the line rather than invalidate it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the condition setting got moved to writeback, execute2 does
nothing aside from wasting a cycle. This removes it.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Check GPRs against any writers in the pipeline.
All instructions are still marked single in pipeline at
this stage.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
This adds combinatorial logic that does 32-bit and 64-bit count
leading and trailing zeroes in one unit, and consolidates the
four instructions under a single OP_CNTZ opcode.
This saves 84 slice LUTs on the Arty A7-100.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Consolidate and/andc/nand, or/orc/nor and xor/eqv, using a common
invert on the input and output. This saves us about 200 LUTs.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
This adds support for set associativity to the icache. It can still
be direct mapped by setting NUM_WAYS to 1.
The replacement policy uses a simple tree-PLRU for each set.
This is only lightly tested, tests pass but I have to double check
that we are using the ways effectively and not creating duplicates.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a new entity 'rotator' which contains combinatorial logic
for rotating and masking 64-bit values. It implements the operations
of the rlwinm, rlwnm, rlwimi, rldicl, rldicr, rldic, rldimi, rldcl,
rldcr, sld, slw, srd, srw, srad, sradi, sraw and srawi instructions.
It consists of a 3-stage 64-bit rotator using 4:1 multiplexors at
each stage, two mask generators, output logic and control logic.
The insn_type_t values used for these instructions have been reduced
to just 5: OP_RLC, OP_RLCL and OP_RLCR for the rotate and mask
instructions (clear both left and right, clear left, clear right
variants), OP_SHL for left shifts, and OP_SHR for right shifts.
The control signals for the rotator are derived from the opcode
and from the is_32bit and is_signed fields of the decode_rom_t.
The rotator is instantiated as an entity in execute1 so that we can
be sure we only have one of it.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
We can now pass both the input clock and target clock frequency
via generics. Add support for both 50Mhz and 100Mhz target freqs
for both cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These are a copy of the A7-35 definitions with 35 changed to 100.
The A7-100 uses the same .xdc file (arty_a7-35.xdc) as the A7-35
since the only difference between the two is the FPGA part; the
hardware and connections on the two boards are identical.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a divider unit, connected to the core in much the same way
that the multiplier unit is connected. The division algorithm is
very simple-minded, taking 64 clock cycles for any division (even
32-bit division instructions).
The decoding is simplified by making use of regularities in the
instruction encoding for div* and mod* instructions. Instead of
having PPC_* encodings from the first-stage decoder for each of the
different div* and mod* instructions, we now just have PPC_DIV and
PPC_MOD, and the inputs to the divider that indicate what sort of
division operation to do are derived from instruction word bits.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a debug module off the DMI (debug) bus which can act as a
wishbone master to generate read and write cycles.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a simple bus that can be mastered from an external
system via JTAG, which will be used to hookup various debug
modules.
It's loosely based on the RiscV model (hence the DMI name).
The module currently only supports hooking up to a Xilinx BSCANE2
but it shouldn't be too hard to adapt it to support different TAPs
if necessary.
The JTAG protocol proper is not exactly the RiscV one at this point,
though I might still change it.
This comes with some sim variants of Xilinx BSCANE2 and BUFG and a
test bench.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras
Michael Neuling
Boris Shingarov