Do more decoding of the instruction ahead of the IDLE state
processing so that the IDLE state code becomes much simpler.
To make the decoding easier, we now use four insn_type_t codes for
floating-point operations rather than two. This also rearranges the
insn_type_t values a little to get the 4 FP opcode values to differ
only in the bottom 2 bits, and put OP_DIV, OP_DIVE and OP_MOD next to
them.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With this, the large case statement sets values for a set of control
signals, which then control multiplexers and adders that generate
values for v.result_exp and v.shift. The plan is for the case
statement to turn into a microcode ROM eventually.
The value of v.result_exp is the sum of two values, either of which
can be negated (but not both). The first value can be chosen from the
result exponent, A exponent, B exponent arithmetically shifted right
one bit, or 0. The second value can be chosen from new_exp (which is
r.result_exp - r.shift), B exponent, C exponent or a constant. The
choices for the constant are 0, 56, the maximum exponent (max_exp) or
the exponent bias for trap-enabled overflow conditions (bias_exp).
These choices are controlled by the signals re_sel1, re_neg1, re_sel2
and re_neg2, and the sum is written into v.result_exp if re_set_result
is 1.
For v.shift we also compute the sum of two values, either of which
can be negated (but not both). The first value can be chosen from
new_exp, B exponent, r.shift, or 0. The second value can be chosen
from the A exponent or a constant. The possible constants are 0, 1,
4, 8, 32, 52, 56, 63, 64, or the minimum exponent (min_exp). These
choices are controlled by the signals rs_sel1, rs_neg1, rs_sel2 and
rs_neg2. After the adder there is a multiplexer which selects either
the sum or a shift count for normalization (derived from a count
leading zeroes operation on R) to be written into v.shift. The
count-leading-zeroes result does not go through the adder for timing
reasons.
In order to simplify the logic and help improve timing, settings of
the control signals have been made unconditional in a state in many
places, even if those settings are only required when some condition
is met.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
In preparation for an explicit exponent data path. The fix is that
fre[s] needs to negate the exponent after renomalization rather than
before, otherwise the exponent adjustment done by the renormalization
is in the wrong direction.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Instead of having a multiplexer in loadstore1 in order to be able to
put the instruction address into v.addr, we now set decode.input_reg_a
to CIA in the decode table entry for OP_FETCH_FAILED. That means that
the operand selection machinery in decode2 will supply the instruction
address to loadstore1 on the lv.addr1 input and no special case is
needed in loadstore1. This saves a few LUTs (~40 on the Artix-7).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This removes some logic that was previously added for the 16-byte
loads and stores (lq, lqarx, stq, stqcx.) and not completely removed
in commit c9e838b656 ("Remove support for lq, stq, lqarx and
stqcx.", 2022-06-04).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
By not assigning to interrupt_out.srr1 in some circumstances, the
writeback_1 process creates an inferred latch, which is not
desirable. Eliminate it by restructuring the code so
interrupt_out.srr1 is always set, to zeroes if nothing else.
Fixes: bc4d02cb0d ("Start removing SPRs from register file", 2022-07-12)
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This fixes a bug which causes a trace interrupt to store the wrong
value in SRR0 in the case where the instruction that has just
completed is followed by a sc (system call) instruction. What happens
is that first the traced instruction sets ex1.trace_next. Then, when
the sc instruction following it comes in, the execute1_actions process
sets v.e.last_nia to next_nia because it is an sc instruction, even
though it is not going to be executed -- we are going to take the
trace interrupt instead. Then when the trace interrupt is taken, we
incorrectly set SRR0 to the incremented address (the address of the
instruction following the sc).
To fix this, we have execute1_actions set a new flag if the current
instruction is sc, and only set v.e.last_nia to next_nia if we
actually execute the sc (in the "if go = '1'" case).
Fixes: 813e2317bf ("execute1: Restructure to separate out execution of side effects", 2022-06-18)
Reported-by: Anton Blanchard <anton@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
xics.vhdl:83:25⚠️ declaration of "v" hides variable "v" [-Whide]
function bswap(v : in std_ulogic_vector(31 downto 0)) return std_ulogic_vector is
xics.vhdl:84:22⚠️ declaration of "r" hides signal "r" [-Whide]
variable r : std_ulogic_vector(31 downto 0);
Signed-off-by: Joel Stanley <joel@jms.id.au>
fpu.vhdl:513:18⚠️ declaration of "result" hides signal "result" [-Whide]
variable result : std_ulogic_vector(63 downto 0);
Signed-off-by: Joel Stanley <joel@jms.id.au>
Regenerate from upstream litex. Something in the update has improved
memory read and write performance quite a lot on my Nexys Video:
Before:
Write speed: 83.2MiB/s
Read speed: 140.4MiB/s
After:
Write speed: 352.1MiB/s
Read speed: 218.5MiB/s
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Fix the litex generate script to pass frequencies in Hz. Regenerate
the litesdcard Verilog for both Xilinx and Lattice. This fixes
litesdcard on my Nexys Video.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Building the mw_debug program leaves build artifacts in
microwatt/scripts/mw_debug
causing noise in the output of `git status`.
This commit adds them to .gitignore.
Signed-off-by: Boris Shingarov <shingarov@labware.com>
The following commit added two tests but didn't update the tests
outputs:
commit 73cc5167ec
Author: Paul Mackerras <paulus@ozlabs.org>
Date: Mon May 9 19:18:42 2022 +1000
Use FPU for division instructions if we have an FPU
This patch updates these using tests/update_console_tests
Signed-off-by: Michael Neuling <mikey@neuling.org>
This improves timing a little because the register addresses now come
directly from a latch instead of being calculated by
decode_input_reg_*. The asserts that check that the two are the same
are now in decode2 rather than register_file.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With this, the register RAM is read synchronously using the addresses
supplied by decode1. That means the register RAM can now be block RAM
rather than LUT RAM.
Debug accesses are done via the B port on cycles when decode1
indicates that there is no valid instruction or the instruction
doesn't use a [F]RB operand.
We latch the addresses being read in each cycle and use the same
address next cycle if stalled. Data that is being written is latched
and a multiplexer on each read port then supplies the latched write
data if the read address for that port equals the write address.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds some relatively simple logic to decode1 to compute the
GPR/FPR addresses that an instruction will access. It always computes
three addresses regardless of whether the instruction will actually
use all of them. The main things it computes are whether the
instruction uses the RS field or the RC field for the 3rd operand, and
whether the operands are FPRs or GPRs (it is possible for RS to be an
FPR but RA and RB to be GPRs, as for example with stfdx).
At the moment all we do with these computed register addresses is to
assert that they are identical to the ones coming from decode2 one
cycle later.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This eliminates one leg of the output value multiplexer, and seems
to improve timing slightly on the A7-100.
Since SPR values are written in stage 3 and read in stage 2, an mfspr
immediately following an mtspr to the same SPR won't give the correct
value. To avoid this, we make mtspr to the load/store SPRs single
issue in decode1.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This provides access to the SPRs via the JTAG DMI interface. For now
they are still accessed as if they were GPR/FPRs using the same
numbering as before (GPRs at 0 - 0x1f, SPRs at 0x20 - 0x2d, FPRs at
0x40 - 0x5f).
For XER, debug reads now report the full value, not just the bits that
were previously stored in the register file. The "slow" SPR mux is
not used for debug reads.
Decode2 determines on each cycle whether a debug SPR access will
happen next cycle, based on whether there is a request and whether the
current instruction accesses the SPR RAM.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With this, the register file now contains 64 entries, for 32 GPRs and
32 FPRs, rather than the 128 it had previously. Several things get
simplified - decode1 no longer has to work out the ispr{1,2,o} values,
decode_input_reg_{a,b,c} no longer have the t = SPR case, etc.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
By putting CTR on the odd side and LR and TAR on the even side, we can
read and write CTR for bdnz-style instructions in parallel with
reading LR or TAR for indirect branches and writing LR for branches
with LK=1. Thus we don't need to double up any of these instructions,
giving a simplification in decode2.
We now have logic for printing LR and CTR at the end of a simulation
in execute1, in addition to the similar logic in register_file and
cr_file.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This starts the process of removing SPRs from the register file by
moving SRR0/1, SPRG0-3, HSRR0/1 and HSPRG0/1 out of the register file
and putting them into execute1. They are stored in a pair of small
RAM arrays, referred to as "even" and "odd". The reason for having
two arrays is so that two values can be read and written in each
cycle. For example, SRR0 and SRR1 can be written in parallel by an
interrupt and read in parallel by the rfid instruction.
The addresses in the RAM which will be accessed are determined in the
decode2 stage. We have one write address for both sides, but two read
addresses, since in future we will want to be able to read CTR at the
same time as either LR or TAR.
We now have a connection from writeback to execute1 which carries the
partial SRR1 value for an interrupt. SRR0 comes from the execute
pipeline; we no longer need to carry instruction addresses along the
LSU and FPU pipelines. Since SRR0 and SRR1 can be written in the same
cycle now, we don't need the little state machine in writeback any
more.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
- Arrange for XER to be written for OE=1 forms
- Arrange for condition codes to be set for RC=1 forms
(including correct handling for 32-bit mode)
- Don't instantiate the divider if we have an FPU.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Anton Blanchard
