Currently, when not using litedram, the top level still has to hook
up "dummy" wishbones to the main dram and control dram busses coming
out of the SoC and provide ack signals.
Instead, make the SoC generate the acks internally when not using
litedram and use defaults to make the wiring entirely optional.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
That way the top-level's don't need to assign them
Also remove generics that are set to the default anyways
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds an SPI flash controller which supports direct
memory-mapped access to the flash along with a manual
mode to send commands.
The direct mode can be set via generic to default to single
wire or quad mode. The controller supports normal, dual and quad
accesses with configurable commands, clock divider, dummy clocks
etc...
The SPI clock can be an even divider of sys_clk starting at 2
(so max 50Mhz with our typical Arty designs).
A flash offset is carried via generics to syscon to tell SW about
which portion of the flash is reserved for the FPGA bitfile. There
is currently no plumbing to make the CPU reset past that address (TBD).
Note: Operating at 50Mhz has proven unreliable without adding some
delay to the sampling of the input data. I'm working in improving
this, in the meantime, I'm leaving the default set at 25 Mhz.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This changes the SoC interconnect such that the main 64-bit wishbone out
of the processor is first split between only 3 slaves (BRAM, DRAM and a
general "IO" bus) instead of all the slaves in the SoC.
The IO bus leg is then latched and down-converted to 32 bits data width,
before going through a second address decoder for the various IO devices.
This significantly reduces routing and timing pressure on the main bus,
allowing to get rid of frequent timing violations when synthetizing on
small'ish FPGAs such as the Artix-7 35T found on the original Arty board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These provides some info about the SoC (though it's still somewhat
incomplete and needs more work, see comments).
There's also a control register for selecting DRAM vs. BRAM at 0
(and for soft-resetting the SoC but that isn't wired up yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
An external signal can control whether the core will start
executing at the standard or the alternate reset address.
This will be used when litedram is initialized by microwatt
itself, to route the reset to the built-in init code secondary
block RAM.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Micropython has been able to fit into 384kB for ages, so lets reduce our
simulated RAM. This is useful for testing if micropython will run on an
ECP5 85k, which has enough BRAM for 384kB but not enough for 512kB.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
This replaces the simple_ram_behavioural and mw_soc_memory modules
with a common wishbone_bram_wrapper.vhdl that interfaces the
pipelined WB with a lower-level RAM module, along with an FPGA
and a sim variants of the latter.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This module adds some simple core controls:
reset, stop, start, step
along with icache clear and reading the NIA and core
status bits
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org
Mikey points out that our stack grows down from 512kB and our
heap is below that too, so we can reduce our BRAM requirements,
which allowing some smaller FPGA boards to work. Not sure why
I thought we were using memory between 512kB and 1MB.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Benjamin Herrenschmidt