Make a few changes to match what mw_debug expects:
- 6 byte instructions
- IDCODE at 001001
- microwatt debug at 000011
Also change IDCODE to be an IBM ID.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
The verilator simulation interface uses the remote_bitbang
protocol from openocd. I have a simple implementation for
urjtag too.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
This fixes a bug in the BTC where entries created for a given address
when MSR[IR] = 0 are used when MSR[IR] = 1 and vice-versa. The fix is
to include r.virt_mode (which mirrors MSR[IR]) in the tag portion of
the BTC.
Fixes: 0fb207be60 ("fetch1: Implement a simple branch target cache", 2020-12-19)
Reported-by: Anton Blanchard <anton@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This fixes a bug which causes a trace interrupt to store the wrong
value in SRR0 in the case where the instruction that has just
completed is followed by a sc (system call) instruction. What happens
is that first the traced instruction sets ex1.trace_next. Then, when
the sc instruction following it comes in, the execute1_actions process
sets v.e.last_nia to next_nia because it is an sc instruction, even
though it is not going to be executed -- we are going to take the
trace interrupt instead. Then when the trace interrupt is taken, we
incorrectly set SRR0 to the incremented address (the address of the
instruction following the sc).
To fix this, we have execute1_actions set a new flag if the current
instruction is sc, and only set v.e.last_nia to next_nia if we
actually execute the sc (in the "if go = '1'" case).
Fixes: 813e2317bf ("execute1: Restructure to separate out execution of side effects", 2022-06-18)
Reported-by: Anton Blanchard <anton@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
xics.vhdl:83:25⚠️ declaration of "v" hides variable "v" [-Whide]
function bswap(v : in std_ulogic_vector(31 downto 0)) return std_ulogic_vector is
xics.vhdl:84:22⚠️ declaration of "r" hides signal "r" [-Whide]
variable r : std_ulogic_vector(31 downto 0);
Signed-off-by: Joel Stanley <joel@jms.id.au>
fpu.vhdl:513:18⚠️ declaration of "result" hides signal "result" [-Whide]
variable result : std_ulogic_vector(63 downto 0);
Signed-off-by: Joel Stanley <joel@jms.id.au>
Regenerate from upstream litex. Something in the update has improved
memory read and write performance quite a lot on my Nexys Video:
Before:
Write speed: 83.2MiB/s
Read speed: 140.4MiB/s
After:
Write speed: 352.1MiB/s
Read speed: 218.5MiB/s
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Fix the litex generate script to pass frequencies in Hz. Regenerate
the litesdcard Verilog for both Xilinx and Lattice. This fixes
litesdcard on my Nexys Video.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Building the mw_debug program leaves build artifacts in
microwatt/scripts/mw_debug
causing noise in the output of `git status`.
This commit adds them to .gitignore.
Signed-off-by: Boris Shingarov <shingarov@labware.com>
The following commit added two tests but didn't update the tests
outputs:
commit 73cc5167ec
Author: Paul Mackerras <paulus@ozlabs.org>
Date: Mon May 9 19:18:42 2022 +1000
Use FPU for division instructions if we have an FPU
This patch updates these using tests/update_console_tests
Signed-off-by: Michael Neuling <mikey@neuling.org>
This improves timing a little because the register addresses now come
directly from a latch instead of being calculated by
decode_input_reg_*. The asserts that check that the two are the same
are now in decode2 rather than register_file.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With this, the register RAM is read synchronously using the addresses
supplied by decode1. That means the register RAM can now be block RAM
rather than LUT RAM.
Debug accesses are done via the B port on cycles when decode1
indicates that there is no valid instruction or the instruction
doesn't use a [F]RB operand.
We latch the addresses being read in each cycle and use the same
address next cycle if stalled. Data that is being written is latched
and a multiplexer on each read port then supplies the latched write
data if the read address for that port equals the write address.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds some relatively simple logic to decode1 to compute the
GPR/FPR addresses that an instruction will access. It always computes
three addresses regardless of whether the instruction will actually
use all of them. The main things it computes are whether the
instruction uses the RS field or the RC field for the 3rd operand, and
whether the operands are FPRs or GPRs (it is possible for RS to be an
FPR but RA and RB to be GPRs, as for example with stfdx).
At the moment all we do with these computed register addresses is to
assert that they are identical to the ones coming from decode2 one
cycle later.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This eliminates one leg of the output value multiplexer, and seems
to improve timing slightly on the A7-100.
Since SPR values are written in stage 3 and read in stage 2, an mfspr
immediately following an mtspr to the same SPR won't give the correct
value. To avoid this, we make mtspr to the load/store SPRs single
issue in decode1.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Anton Blanchard
