Currently the test writes to the XICS and then checks that the
expected interrupt has happened. This turns into a stbcix
instruction followed immediately by a load from the variable that
indicates whether an interrupt has happened. It is possible for
it to take a few cycles for the store to reach the XICS and the
interrupt request signal to come back to the core, particularly
with improvements to the load/store unit and dcache.
This therefore adds a delay between storing to the XICS and
checking for the occurrence of an interrupt, so as to give the
signals time to propagate. The delay loop does an arbitrary 10
iterations, and each iteration does two loads and one store to
(cacheable) memory.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The two tests obtain NIA with bl+mflr+addi and then compare it
against addpcis with the minimum and maximum immediate operand values.
They were also tested on a real POWER9 system (in userspace) for good
measure.
Signed-off-by: Shawn Anastasio <shawn@anastas.io>
This changes the SoC interconnect such that the main 64-bit wishbone out
of the processor is first split between only 3 slaves (BRAM, DRAM and a
general "IO" bus) instead of all the slaves in the SoC.
The IO bus leg is then latched and down-converted to 32 bits data width,
before going through a second address decoder for the various IO devices.
This significantly reduces routing and timing pressure on the main bus,
allowing to get rid of frequent timing violations when synthetizing on
small'ish FPGAs such as the Artix-7 35T found on the original Arty board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
console.c goes to a new lib/ where we'll store other general utilities
and console.h goes to include/
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It makes things a bit more standard and a bit nicer to read
without all those strlen(). Also console.c takes care of adding
the carriage returns before the linefeeds.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This uses the new header files for register definitions and
extracts the core frequency from syscon rather than hard coding it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the PID register and repurposes SPR 720 as the PRTBL
register, which points to the base of the process table. There
doesn't seem to be any point to implementing the partition table given
that we don't have hypervisor mode.
The MMU caches entry 0 of the process table internally (in pgtbl3)
plus the entry indexed by the value in the PID register (pgtbl0).
Both caches are invalidated by a tlbie[l] with RIC=2 or by a move to
PRTBL. The pgtbl0 cache is invalidated by a move to PID. The dTLB
and iTLB are cleared by a move to either PRTBL or PID.
Which of the two page table root pointers is used (pgtbl0 or pgtbl3)
depends on the MSB of the address being translated. Since the segment
checking ensures that address(63) = address(62), this is sufficient to
map quadrants 0 and 3.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Since setting MSR[PR] = 1 forces instruction translation on, we need
to set up translations for the problem state code to use.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds tests of instruction translation to the mmu test.
This also clears the BSS and improves the linker script.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds tests to check that the MMU and dTLB are translating
addresses and checking permissions correctly.
We use a simple 2-level radix tree. The radix tree maps 2GB of
address space and has a 1024-entry page directory pointing to
512-entry page table pages.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a test that tries to execute various privileged instructions
with MSR[PR] = 1. This also incidentally tests some of the MSR bit
manipulations.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Checks interrupt masking and priorities.
Adds to `make test_xics` which is run in `make check` also.
Signed-off-by: Michael Neuling <mikey@neuling.org>
This puts an attn instruction at offset 0x700 in each of the tests
so that the test will terminate if a program interrupt is taken.
This means that we can implement the tw instruction to cause a
program interrupt.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This fixes the decrementer, illegal and sc tests to compile
successfully with cross-compilers that don't provide unistd.h
or string.h. Instead of those headers we include stddef.h.
This also fixes tests/Makefile.test to do what one expects
when CROSS_COMPILE is defined in the environment.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds test cases for:
- sc, illegals and decrementer exceptions
- decrementer overflow
- rfid
- mt/mf sprg0/1 srr0/1
- mtdec
- mtmsrd
- sc
It also adds these test cases to make check/check_light
Signed-off-by: Michael Neuling <mikey@neuling.org>
Right now our test cases fold the SPRs into the GPRs. That makes
debugging fails more difficult than it needs to be, so print
out the CTR, LR and CR.
We still need to print the XER, but that is in two spots in microwatt
and will take some more work.
This also adds many instructions to the tests that we have added
lately including overflow instructions, CR logicals and mt/mfxer.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Benjamin Herrenschmidt
Paul Mackerras
Michael Neuling