Commit Graph

73 Commits (047be5c0c3b2f12c9321412518e17b7267fe14ea)

Author SHA1 Message Date
Paul Mackerras 047be5c0c3 loadstore1: Do SPR reading in stage 2 rather than stage 3
This eliminates one leg of the output value multiplexer, and seems
to improve timing slightly on the A7-100.

Since SPR values are written in stage 3 and read in stage 2, an mfspr
immediately following an mtspr to the same SPR won't give the correct
value.  To avoid this, we make mtspr to the load/store SPRs single
issue in decode1.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
Paul Mackerras af814a0d5e Provide debug access to SPRs in loadstore1 and mmu
They are accessible as GSPR 0x3c - PID, 0x3d - PTCR, 0x3e - DSISR
and 0x3f - DAR.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
Paul Mackerras fdb3ef6874 Finish off taking SPRs out of register file
With this, the register file now contains 64 entries, for 32 GPRs and
32 FPRs, rather than the 128 it had previously.  Several things get
simplified - decode1 no longer has to work out the ispr{1,2,o} values,
decode_input_reg_{a,b,c} no longer have the t = SPR case, etc.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
Paul Mackerras bc4d02cb0d Start removing SPRs from register file
This starts the process of removing SPRs from the register file by
moving SRR0/1, SPRG0-3, HSRR0/1 and HSPRG0/1 out of the register file
and putting them into execute1.  They are stored in a pair of small
RAM arrays, referred to as "even" and "odd".  The reason for having
two arrays is so that two values can be read and written in each
cycle.  For example, SRR0 and SRR1 can be written in parallel by an
interrupt and read in parallel by the rfid instruction.

The addresses in the RAM which will be accessed are determined in the
decode2 stage.  We have one write address for both sides, but two read
addresses, since in future we will want to be able to read CTR at the
same time as either LR or TAR.

We now have a connection from writeback to execute1 which carries the
partial SRR1 value for an interrupt.  SRR0 comes from the execute
pipeline; we no longer need to carry instruction addresses along the
LSU and FPU pipelines.  Since SRR0 and SRR1 can be written in the same
cycle now, we don't need the little state machine in writeback any
more.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
Paul Mackerras c9e838b656 Remove support for lq, stq, lqarx and stqcx.
They are optional in SFFS (scalar fixed-point and floating-point
subset), are not needed for running Linux, and add complexity, so
remove them.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
Paul Mackerras 9a8a8e50f8 FPU: Add stage-2 stall ability to FPU
This makes the FPU able to stall other units at execute stage 2 and be
stalled by other units (specifically the LSU).

This means that the completion and writeback for an instruction can
now end up being deferred until the second cycle of a following
instruction, i.e. the cycle when the state machine has gone through
IDLE state into one of the DO_* states, which means we need to latch
the destination FPR number, CR mask, etc. from the previous
instruction so that we present the correct information to writeback.

The advantage of this is that we can get rid of the in_progress signal
from the LSU.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
Paul Mackerras e030a500e8 Allow integer instructions and load/store instructions to execute together
Execute1 and loadstore1 now send each other stall signals that
indicate that a valid instruction in stage 2 can't complete in this
cycle, and hence any valid instruction in stage 1 in the other unit
can't move to stage 2.  With this in place, an ALU instruction can
move into stage 1 while a LSU instruction is in stage 2.

Since the FPU doesn't yet have a way to stall completion, we can't yet
start FPU instructions while any LSU or ALU instruction is in
progress.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
Paul Mackerras bdd4d04162 Simplify flow control in the dcache and loadstore units
Simplify the flow control by stalling the whole upstream pipeline when
a stage can't proceed, instead of trying to let each stage progress
independently when it can.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
Anton Blanchard b47b71821e loadstore1: reduce U state being output
While these signals should only be read when valid is true, they
are only a small number of bits and we want to reduce the amount of
U/X state bouncing around the chip.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
2 years ago
Anton Blanchard e2438071a1 loadstore1: Initialise PMU events
The loadstore1 PMU events are U state until a load and a store completes.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
2 years ago
Paul Mackerras bb5f356386 loadstore1: Make r1.req.addr not depend on l_in.valid
Some critical path reports showed r1.req.addr depending on l_in.valid,
which then depended ultimately on the dcache's r1.ls_valid.  In fact
we can update r1.req.addr (and other fields of r1.req, except for
r1.req.valid) independently of l_in.valid as long as busy = 0.
We do also need to preserve r1.req.addr0 when l_in.valid = 0, so we
pull it out of r1.req and store it separately in r1.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
3 years ago
Paul Mackerras 65c43b488b PMU: Add several more events
This implements most of the architected PMU events.  The ones missing
are mostly the ones that depend on which level of the cache hierarchy
data is fetched from.  The events implemented here, and their raw
event codes, are:

    Floating-point operation completed (100f4)
    Load completed (100fc)
    Store completed (200f0)
    Icache miss (200fc)
    ITLB miss (100f6)
    ITLB miss resolved (400fc)
    Dcache load miss (400f0)
    Dcache load miss resolved (300f8)
    Dcache store miss (300f0)
    DTLB miss (300fc)
    DTLB miss resolved (200f6)
    No instruction available and none being executed (100f8)
    Instruction dispatched (200f2, 300f2, 400f2)
    Taken branch instruction completed (200fa)
    Branch mispredicted (400f6)
    External interrupt taken (200f8)

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
3 years ago
Paul Mackerras 64e3ce7134 execute1: Handle interrupts during sequences of load/store operations
At present the logic prevents any interrupts from being handled while
there is a load/store instruction (one that has unit=LDST) being
executed.  However, load/store instructions can still get sent to
loadstore1.  Thus an instruction which should generate an interrupt
such as a floating-point unavailable interrupt will instead get
executed.

To fix this, when we detect that an interrupt should be generated but
loadstore1 is still executing a previous instruction, we don't execute
any new instructions, and set a new r.intr_pending flag.  That results
in busy_out being asserted (meaning that no further instructions will
come in from decode2).  When loadstore1 has finished the instructions
it has, the interrupt gets sent to writeback.  If one of the
instructions in loadstore1 generates an interrupt in the meantime, the
l_in.interrupt signal gets asserted and that clears r.intr_pending, so
the interrupt we detected gets discarded.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
3 years ago
Paul Mackerras 18120f153d MMU: Implement a vestigial partition table
This implements a 1-entry partition table, so that instead of getting
the process table base address from the PRTBL SPR, the MMU now reads
the doubleword pointed to by the PTCR register plus 8 to get the
process table base address.  The partition table entry is cached.

Having the PTCR and the vestigial partition table reduces the amount
of software change required in Linux for Microwatt support.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
3 years ago
Michael Neuling 4c21587c4d Fix DAR/DSISR reading before they are written
If the DAR and DSISR are read before they are written, we assert with:

  register_file.vhdl:55:25:@60195ns:(report note): Writing GPR 09 00000000XXXXXXXX
  register_file.vhdl:61:17:@60195ns:(assertion failure): Assertion violation

This initialises DAR/DSISR to avoid this.

Signed-off-by: Michael Neuling <mikey@neuling.org>
3 years ago
Paul Mackerras 17fd069640 core: Allow multiple loadstore instructions to be in flight
The idea here is that we can have multiple instructions in progress at
the same time as long as they all go to the same unit, because that
unit will keep them in order.  If we get an instruction for a
different unit, we wait for all the previous instructions to finish
before executing it.  Since the loadstore unit is the only one that is
currently pipelined, this boils down to saying that loadstore
instructions can go ahead while l_in.in_progress = 1 but other
instructions have to wait until it is 0.

This gives a 2% increase on coremark performance on the Arty A7-100
(from ~190 to ~194).

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras f583d088b7 loadstore: Convert to 3-stage pipeline
This makes loadstore use a 3-stage pipeline.  For now, only one
instruction goes through the pipe at a time.  Completion and writeback
are still combinatorial off the valid signal back from the dcache, so
performance should be the same as before.  In future it should be able
to sustain one load or store per cycle provided they hit in the
dcache.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras f636bb7c39 dcache: Fix bugs in pipelined operation
This fixes two bugs which show up when multiple operations are in
flight in the dcache, and adds a 'hold' input which will be needed
when loadstore1 is pipelined.

The first bug is that dcache needs to sample the data for a store on
the cycle after the store request comes in even if the store request
is held up because of a previous request (e.g. if the previous request
is a load miss or a dcbz).

The second bug is that a load request coming in for a cache line being
refilled needs to be handled immediately in the case where it is for
the row whose data arrives on the same cycle.  If it is not, then it
will be handled as a separate cache miss and the cache line will be
refilled again into a different way, leading to two ways both being
valid for the same tag.  This can lead to data corruption, in the
scenario where subsequent writes go to one of the ways and then that
way gets displaced but the other way doesn't.  This bug could in
principle show up even without having multiple operations in flight in
the dcache.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras acb3d2d745 core: Send FPU interrupts to writeback rather than execute1
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 29221315e9 core: Send loadstore1 interrupts to writeback rather than execute1
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras c0b45e153b core: Track GPR hazards using tags that propagate through the pipelines
This changes the way GPR hazards are detected and tracked.  Instead of
having a model of the pipeline in gpr_hazard.vhdl, which has to mirror
the behaviour of the real pipeline exactly, we now assign a 2-bit tag
to each instruction and record which GSPR the instruction writes.
Subsequent instructions that need to use the GSPR get the tag number
and stall until the value with that tag is being written back to the
register file.

For now, the forwarding paths are disabled.  That gives about a 8%
reduction in coremark performance.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 4c61a71a62 core: Crack update-form loads into two internal ops
This uses the instruction-doubling machinery to send load with update
instructions down to loadstore1 as two separate ops, rather than
one op with two destinations.  This will help to simplify the value
tracking mechanisms.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 6427cab46f loadstore1/dcache: Send store data one cycle later
This makes timing easier and also means that store floating-point
single precision instructions no longer need to take an extra cycle.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras d1f35705c0 loadstore1: Improve timing of data path from cache RAM to writeback
Work out select inputs for writeback mux a cycle earlier.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 54f89afab7 loadstore1: Decide on load formatting controls a cycle earlier
This helps timing.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 89a67a18d0 decode: Add a facility field to the instruction decode tables
This makes it simpler to work out when to deliver a FPU unavailable
interrupt.  This also means we can get rid of the OP_FPLOAD and
OP_FPSTORE insn_type values.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 4b2c23703c core: Implement quadword loads and stores
This implements the lq, stq, lqarx and stqcx. instructions.

These instructions all access two consecutive GPRs; for example the
"lq %r6,0(%r3)" instruction will load the doubleword at the address
in R3 into R7 and the doubleword at address R3 + 8 into R6.  To cope
with having two GPR sources or destinations, the instruction gets
repeated at the decode2 stage, that is, for each lq/stq/lqarx/stqcx.
coming in from decode1, two instructions get sent out to execute1.

For these instructions, the RS or RT register gets modified on one
of the iterations by setting the LSB of the register number.  In LE
mode, the first iteration uses RS|1 or RT|1 and the second iteration
uses RS or RT.  In BE mode, this is done the other way around.  In
order for decode2 to know what endianness is currently in use, we
pass the big_endian flag down from icache through decode1 to decode2.
This is always in sync with what execute1 is using because only rfid
or an interrupt can change MSR[LE], and those operations all cause
a flush and redirect.

There is now an extra column in the decode tables in decode1 to
indicate whether the instruction needs to be repeated.  Decode1 also
enforces the rule that lq with RT = RT and lqarx with RA = RT or
RB = RT are illegal.

Decode2 now passes a 'repeat' flag and a 'second' flag to execute1,
and execute1 passes them on to loadstore1.  The 'repeat' flag is set
for both iterations of a repeated instruction, and 'second' is set
on the second iteration.  Execute1 does not take asynchronous or
trace interrupts on the second iteration of a repeated instruction.

Loadstore1 uses 'next_addr' for the second iteration of a repeated
load/store so that we access the second doubleword of the memory
operand.  Thus loadstore1 accesses the doublewords in increasing
memory order.  For 16-byte loads this means that the first iteration
writes GPR RT|1.  It is possible that RA = RT|1 (this is a legal
but non-preferred form), meaning that if the memory operand was
misaligned, the first iteration would overwrite RA but then the
second iteration might take a page fault, leading to corrupted state.
To avoid that possibility, 16-byte loads in LE mode take an
alignment interrupt if the operand is not 16-byte aligned.  (This
is the case anyway for lqarx, and we enforce it for lq as well.)

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 9d285a265c core: Add support for single-precision FP loads and stores
This adds code to loadstore1 to convert between single-precision and
double-precision formats, and implements the lfs* and stfs*
instructions.  The conversion processes are described in Power ISA
v3.1 Book 1 sections 4.6.2 and 4.6.3.

These conversions take one cycle, so lfs* and stfs* are one cycle
slower than lfd* and stfd*.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 45cd8f4fc3 core: Add support for floating-point loads and stores
This extends the register file so it can hold FPR values, and
implements the FP loads and stores that do not require conversion
between single and double precision.

We now have the FP, FE0 and FE1 bits in MSR.  FP loads and stores
cause a FP unavailable interrupt if MSR[FP] = 0.

The FPU facilities are optional and their presence is controlled by
the HAS_FPU generic passed down from the top-level board file.  It
defaults to true for all except the A7-35 boards.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras eee90a0815 loadstore1: Generate alignment interrupts for unaligned larx/stcx
Load-and-reserve and store-conditional instructions are required to
generate an alignment interrupt (0x600 vector) if their EA is not
aligned.  Implement this.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 033ee909fd core: Implement 32-bit mode
In 32-bit mode, effective addresses are truncated to 32 bits, both for
instruction fetches and data accesses, and CR0 is set for Rc=1 (record
form) instructions based on the lower 32 bits of the result rather
than all 64 bits.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 2e7b371305 core: Implement big-endian mode
Big-endian mode affects both instruction fetches and data accesses.
For instruction fetches, we byte-swap each word read from memory when
writing it into the icache data RAM, and use a tag bit to indicate
whether each cache line contains instructions in BE or LE form.

For data accesses, we simply need to invert the existing byte_reverse
signal in BE mode.  The only thing to be careful of is to get the sign
bit from the correct place when doing a sign-extending load that
crosses two doublewords of memory.

For now, interrupts unconditionally set MSR[LE].  We will need some
sort of interrupt-little-endian bit somewhere, perhaps in LPCR.

This also fixes a debug report statement in fetch1.vhdl.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras ea0b843662 loadstore1: Better expression for store data formatting
This rearranges the code used for store data formatting so that the
"for i in 0 to 7" loop indexes the output bytes rather than the
input bytes.  The new expression is formally identical to the old
but is easier to synthesize.  This reduces the number of LUTs by
about 250 on the Artix-7 and improves timing.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 2cb1d7671e loadstore1: Further tweaks to improve synthesis with yosys/nextpnr
This reworks the way that the busy and done signals are generated in
loadstore in order to work around some problems where yosys/nextpnr
are reporting combinatorial loops (not in fact on the current code but
on minor variations needed for supporting the FPU).  It seems that
yosys has problems with the case statement on v.state.

This also lifts the maddr and byte_sel generation out of the case
statement.  The overall result is a slight reduction in resource usage
(~30 6-input LUTs on the A7-100).

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras b80e81e123 loadstore1: Separate address calculation for MMU to ease timing
This computes the address sent to the MMU separately from that sent
to the dcache.  This means that the address sent to the MMU doesn't
have the delay through the lsu_sum adder, making it available earlier.
The path through the lsu_sum adder and through the MMU to the MMU
done and err outputs showed up as a critical path on some builds.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 91cbeee77c loadstore1: Generate busy signal earlier
This makes the calculation of busy as simple as possible and dependent
only on register outputs.  The timing of busy is critical, as it gates
the valid signal for the next instruction, and therefore any delays
in dropping busy at the end of a load or store directly impact the
timing of a host of other paths.

This also separates the 'done without error' and 'done with error'
cases from the MMU into separate signals that are both driven directly
from registers.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras c180ed0af0 dcache: Output separate done-without-error and error-done signals
This reduces the complexity of the logic in the places where these
signals are used.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 893d2bc6a2 core: Don't generate logic for log data when LOG_LENGTH = 0
This adds "if LOG_LENGTH > 0 generate" to the places in the core
where log output data is latched, so that when LOG_LENGTH = 0 we
don't create the logic to collect the data which won't be stored.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras b2ba024a48 loadstore1: Eliminate two_dwords variable
The computation of two_dwords from r.second_bytes has shown up as
part of a critical path at times.  Instead we add a 'last_dword'
flag to the reg_stage_t record which tells us more directly
whether a valid flag coming in from dcache means that the
instruction is done, thereby shortening the path to the busy output
back to execute1.

This also simplifies some of the trim_ctl logic.  The two_dwords = 0
case could never have use_second(i) = 1 for any of the bytes being
transferred, so "not use_second(i)" is always 1.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 209aa9ce3f loadstore1: Reduce busy cycles
This reduces the number of cycles where loadstore1 asserts its busy
output, leading to increased throughput of loads and stores.  Loads
that hit in the cache can now be executed at the rate of one every two
cycles.  Stores take 4 cycles assuming the wishbone slave responds
with an ack the cycle after we assert strobe.

To achieve this, the state machine code is split into two parts, one
for when we have an existing instruction in progress, and one for
starting a new instruction.  We can now combinatorially clear busy and
start a new instruction in the same cycle that we get a done signal
from the dcache; in other words we are completing one instruction and
potentially writing back results in the same cycle that we start a new
instruction and send its address and data to the dcache.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 1d09daae03 loadstore1: Complete mfspr/mtspr a cycle later
This makes mfspr and mtspr complete (and mfspr write back) on the
cycle after the instruction is received from execute1, rather than
on the same cycle.  This makes them match all other instructions
that execute in one cycle.  Because these instructions are marked
as single-issue, there wasn't the possibility of having two
instructions complete on the same cycle (which we can't cope with),
but it is better to fix this.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 6701e7346b core: Use a busy signal rather than a stall
This changes the instruction dependency tracking so that we can
generate a "busy" signal from execute1 and loadstore1 which comes
along one cycle later than the current "stall" signal.  This will
enable us to signal busy cycles only when we need to from loadstore1.

The "busy" signal from execute1/loadstore1 indicates "I didn't take
the thing you gave me on this cycle", as distinct from the previous
stall signal which meant "I took that but don't give me anything
next cycle".  That means that decode2 proactively gives execute1
a new instruction as soon as it has taken the previous one (assuming
there is a valid instruction available from decode1), and that then
sits in decode2's output until execute1 can take it.  So instructions
are issued by decode2 somewhat earlier than they used to be.

Decode2 now only signals a stall upstream when its output buffer is
full, meaning that we can fill up bubbles in the upstream pipe while a
long instruction is executing.  This gives a small boost in
performance.

This also adds dependency tracking for rA updates by update-form
load/store instructions.

The GPR and CR hazard detection machinery now has one extra stage,
which may not be strictly necessary.  Some of the code now really
only applies to PIPELINE_DEPTH=1.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 49a4d9f67a Add core logging
This logs 256 bits of data per cycle to a ring buffer in BRAM.  The
data collected can be read out through 2 new SPRs or through the
debug interface.

The new SPRs are LOG_ADDR (724) and LOG_DATA (725).  LOG_ADDR contains
the buffer write pointer in the upper 32 bits (in units of entries,
i.e. 32 bytes) and the read pointer in the lower 32 bits (in units of
doublewords, i.e. 8 bytes).  Reading LOG_DATA gives the doubleword
from the buffer at the read pointer and increments the read pointer.
Setting bit 31 of LOG_ADDR inhibits the trace log system from writing
to the log buffer, so the contents are stable and can be read.

There are two new debug addresses which function similarly to the
LOG_ADDR and LOG_DATA SPRs.  The log is frozen while either or both of
the LOG_ADDR SPR bit 31 or the debug LOG_ADDR register bit 31 are set.

The buffer defaults to 2048 entries, i.e. 64kB.  The size is set by
the LOG_LENGTH generic on the core_debug module.  Software can
determine the length of the buffer because the length is ORed into the
buffer write pointer in the upper 32 bits of LOG_ADDR.  Hence the
length of the buffer can be calculated as 1 << (31 - clz(LOG_ADDR)).

There is a program to format the log entries in a somewhat readable
fashion in scripts/fmt_log/fmt_log.c.  The log_entry struct in that
file describes the layout of the bits in the log entries.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 2843c99a71 MMU: Implement reading of the process table
This adds the PID register and repurposes SPR 720 as the PRTBL
register, which points to the base of the process table.  There
doesn't seem to be any point to implementing the partition table given
that we don't have hypervisor mode.

The MMU caches entry 0 of the process table internally (in pgtbl3)
plus the entry indexed by the value in the PID register (pgtbl0).
Both caches are invalidated by a tlbie[l] with RIC=2 or by a move to
PRTBL.  The pgtbl0 cache is invalidated by a move to PID.  The dTLB
and iTLB are cleared by a move to either PRTBL or PID.

Which of the two page table root pointers is used (pgtbl0 or pgtbl3)
depends on the MSB of the address being translated.  Since the segment
checking ensures that address(63) = address(62), this is sufficient to
map quadrants 0 and 3.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras a658766fcf Implement slbia as a dTLB/iTLB flush
Slbia (with IH=7) is used in the Linux kernel to flush the ERATs
(our iTLB/dTLB), so make it do that.

This moves the logic to work out whether to flush a single entry
or the whole TLB from dcache and icache into mmu.  We now invalidate
all dTLB and iTLB entries when the AP (actual pagesize) field of
RB is non-zero on a tlbie[l], as well as when IS is non-zero.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 01046527ba MMU: Do radix page table walks on iTLB misses
This hooks up the connections so that an OP_FETCH_FAILED coming down
to loadstore1 will get sent to the MMU for it to do a radix tree walk
for the instruction address.  The MMU then sends the resulting PTE to
the icache module to be installed in the iTLB.  If no valid PTE can
be found, the MMU sends an error signal back to loadstore1 which sends
it on to execute1 to generate an ISI.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 3d4712ad43 Add TLB to icache
This adds a direct-mapped TLB to the icache, with 64 entries by default.
Execute1 now sends a "virt_mode" signal from MSR[IR] to fetch1 along
with redirects to indicate whether instruction addresses should be
translated through the TLB, and fetch1 sends that on to icache.
Similarly a "priv_mode" signal is sent to indicate the privilege
mode for instruction fetches.  This means that changes to MSR[IR]
or MSR[PR] don't take effect until the next redirect, meaning an
isync, rfid, branch, etc.

The icache uses a hash of the effective address (i.e. next instruction
address) to index the TLB.  The hash is an XOR of three fields of the
address; with a 64-entry TLB, the fields are bits 12--17, 18--23 and
24--29 of the address.  TLB invalidations simply invalidate the
indexed TLB entry without checking the contents.

If the icache detects a TLB miss with virt_mode=1, it will send a
fetch_failed indication through fetch2 to decode1, which will turn it
into a special OP_FETCH_FAILED opcode with unit=LDST.  That will get
sent down to loadstore1 which will currently just raise a Instruction
Storage Interrupt (0x400) exception.

One bit in the PTE obtained from the TLB is used to check whether an
instruction access is allowed -- the privilege bit (bit 3).  If bit 3
is 1 and priv_mode=0, then a fetch_failed indication is sent down to
fetch2 and to decode1, which generates an OP_FETCH_FAILED.  Any PTEs
with PTE bit 0 (EAA[3]) clear or bit 8 (R) clear should not be put
into the iTLB since such PTEs would not allow execution by any
context.

Tlbie operations get sent from mmu to icache over a new connection.

Unfortunately the privileged instruction tests are broken for now.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 3eb07dc637 MMU: Refetch PTE on access fault
This is required by the architecture.  It means that the error bits
reported in DSISR or SRR1 now come from the permission/RC check done
on the refetched PTE rather than the TLB entry.  Unfortunately that
somewhat breaks the software-loaded TLB mode of operation in that
DSISR/SRR1 always report no PTE rather than permission error or
RC failure.

This also restructures the loadstore1 state machine a bit, combining
the FIRST_ACK_WAIT and LAST_ACK_WAIT states into a single state and
the MMU_LOOKUP_1ST and MMU_LOOKUP_LAST states likewise.  We now have a
'dwords_done' bit to say whether the first transfer of two (for an
unaligned access) has been done.

The cache paradox error (where a non-cacheable access finds a hit in
the cache) is now the only cause of DSI from the dcache.  This should
probably be a machine check rather than DSI in fact.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras f6a0d7f9da MMU: Implement data segment interrupts
A data segment interrupt (DSegI) occurs when an address to be
translated by the MMU is outside the range of the radix tree
or the top two bits of the address (the quadrant) are 01 or 10.
This is detected in a new state of the MMU state machine, and
is sent back to loadstore1 as an error, which sends it on to
execute1 to generate an interrupt to the 0x380 vector.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
Paul Mackerras 4e6fc6811a MMU: Implement radix page table machinery
This adds the necessary machinery to the MMU for it to do radix page
table walks.  The core elements are a shifter that can shift the
address right by between 0 and 47 bits, a mask generator that can
generate a mask of between 5 and 16 bits, a final mask generator,
and new states in the state machine.

(The final mask generator is used for transferring bits of the
original address into the resulting TLB entry when the leaf PTE
corresponds to a page size larger than 4kB.)

The hardware does not implement a partition table or a process table.
Software is expected to load the appropriate process table entry
into a new SPR called PGTBL0, SPR 720.  The contents should be
formatted as described in Book III section 5.7.6.2 of the Power ISA
v3.0B.  PGTBL0 is set to 0 on hard reset.  At present, the top two bits
of the address (the quadrant) are ignored.

There is currently no caching of any step in the translation process
or of the final result, other than the entry created in the dTLB.
That entry is a 4k page entry even if the leaf PTE found in the walk
corresponds to a larger page size.

This implementation can handle almost any page table layout and any
page size.  The RTS field (in PGTBL0) can have any value between 0
and 31, corresponding to a total address space size between 2^31
and 2^62 bytes.  The RPDS field of PGTBL0 can be any value between
5 and 16, except that a value of 0 is taken to disable radix page
table walking (for use when one is using software loading of TLB
entries).  The NLS field of the page directory entries can have any
value between 5 and 16.  The minimum page size is 4kB, meaning that
the sum of RPDS and the NLS values of the PDEs found on the path to
a leaf PTE must be less than or equal to RTS + 31 - 12.

The PGTBL0 SPR is in the mmu module; thus this adds a path for
loadstore1 to read and write SPRs in mmu.  This adds code in dcache
to service doubleword read requests from the MMU, as well as requests
to write dTLB entries.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago