loadstore1: Complete mfspr/mtspr a cycle later

This makes mfspr and mtspr complete (and mfspr write back) on the
cycle after the instruction is received from execute1, rather than
on the same cycle.  This makes them match all other instructions
that execute in one cycle.  Because these instructions are marked
as single-issue, there wasn't the possibility of having two
instructions complete on the same cycle (which we can't cope with),
but it is better to fix this.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

loadstore1.vhdl

@@ -42,7 +42,8 @@ architecture behave of loadstore1 is
                      ACK_WAIT,          -- waiting for ack from dcache
                      LD_UPDATE,         -- writing rA with computed addr on load
                      MMU_LOOKUP,        -- waiting for MMU to look up translation
-                     TLBIE_WAIT         -- waiting for MMU to finish doing a tlbie
+                     TLBIE_WAIT,        -- waiting for MMU to finish doing a tlbie
+                     SPR_CMPLT          -- complete a mf/tspr operation
                      );
 
     type reg_stage_t is record
@@ -51,6 +52,7 @@ architecture behave of loadstore1 is
         load         : std_ulogic;
         tlbie        : std_ulogic;
         dcbz         : std_ulogic;
+        mfspr        : std_ulogic;
 	addr         : std_ulogic_vector(63 downto 0);
 	store_data   : std_ulogic_vector(63 downto 0);
 	load_data    : std_ulogic_vector(63 downto 0);
@@ -73,6 +75,7 @@ architecture behave of loadstore1 is
         dar          : std_ulogic_vector(63 downto 0);
         dsisr        : std_ulogic_vector(31 downto 0);
         instr_fault  : std_ulogic;
+        sprval       : std_ulogic_vector(63 downto 0);
     end record;
 
     type byte_sel_t is array(0 to 7) of std_ulogic;
@@ -152,9 +155,7 @@ begin
         variable use_second : byte_sel_t;
         variable trim_ctl : trim_ctl_t;
         variable negative : std_ulogic;
-        variable mfspr : std_ulogic;
         variable sprn : std_ulogic_vector(9 downto 0);
-        variable sprval : std_ulogic_vector(63 downto 0);
         variable exception : std_ulogic;
         variable next_addr : std_ulogic_vector(63 downto 0);
         variable mmureq : std_ulogic;
@@ -168,11 +169,10 @@ begin
         done := '0';
         byte_sel := (others => '0');
         addr := lsu_sum;
-        mfspr := '0';
+        v.mfspr := '0';
         mmu_mtspr := '0';
         itlb_fault := '0';
         sprn := std_ulogic_vector(to_unsigned(decode_spr_num(l_in.insn), 10));
-        sprval := (others => '0');      -- avoid inferred latches
         exception := '0';
         dsisr := (others => '0');
         mmureq := '0';
@@ -256,20 +256,20 @@ begin
                     v.tlbie := '1';
                     v.state := TLBIE_WAIT;
                 when OP_MFSPR =>
-                    done := '1';
-                    mfspr := '1';
+                    v.mfspr := '1';
                     -- partial decode on SPR number should be adequate given
                     -- the restricted set that get sent down this path
                     if sprn(9) = '0' and sprn(5) = '0' then
                         if sprn(0) = '0' then
-                            sprval := x"00000000" & r.dsisr;
+                            v.sprval := x"00000000" & r.dsisr;
                         else
-                            sprval := r.dar;
+                            v.sprval := r.dar;
                         end if;
                     else
                         -- reading one of the SPRs in the MMU
-                        sprval := m_in.sprval;
+                        v.sprval := m_in.sprval;
                     end if;
+                    v.state := SPR_CMPLT;
                 when OP_MTSPR =>
                     if sprn(9) = '0' and sprn(5) = '0' then
                         if sprn(0) = '0' then
@@ -277,7 +277,7 @@ begin
                         else
                             v.dar := l_in.data;
                         end if;
-                        done := '1';
+                        v.state := SPR_CMPLT;
                     else
                         -- writing one of the SPRs in the MMU
                         mmu_mtspr := '1';
@@ -452,6 +452,10 @@ begin
             v.state := IDLE;
             done := '1';
 
+        when SPR_CMPLT =>
+            done := '1';
+            v.state := IDLE;
+
         end case;
 
         -- Update outputs to dcache
@@ -482,10 +486,10 @@ begin
         -- Multiplex either cache data to the destination GPR or
         -- the address for the rA update.
         l_out.valid <= done;
-        if mfspr = '1' then
+        if r.mfspr = '1' then
             l_out.write_enable <= '1';
-            l_out.write_reg <= l_in.write_reg;
-            l_out.write_data <= sprval;
+            l_out.write_reg <= r.write_reg;
+            l_out.write_data <= r.sprval;
         elsif do_update = '1' then
             l_out.write_enable <= '1';
             l_out.write_reg <= r.update_reg;