Make a few changes to match what mw_debug expects:
- 6 byte instructions
- IDCODE at 001001
- microwatt debug at 000011
Also change IDCODE to be an IBM ID.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
The verilator simulation interface uses the remote_bitbang
protocol from openocd. I have a simple implementation for
urjtag too.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
This makes it easier to parse the records in verilog because they
are getting flattened into an array of bits by ghdl/yosys.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
The ability to stop the core using the debug interface has been broken
since commit bb4332b7e6b5 ("Remove fetch2 pipeline stage"), which
removed a statement that cleared the valid bit on instructions when
their stop_mark was 1.
Fix this by clearing r.req coming out of fetch1 when r.stop_mark = 1.
This has the effect of making i_out.valid be 0 from the icache. We
also fix a bug in icache.vhdl where it was not honouring i_in.req when
use_previous = 1.
It turns out that the logic in fetch1.vhdl to handle stopping and
restarting was not correct, with the effect that stopping the core
would leave NIA pointing to the last instruction executed, not the
next instruction to be executed. In fact the state machine is
unnecessary and the whole thing can be simplified enormously - we
need to increment NIA whenever stop_in = 0 in the previous cycle.
Fixes: bb4332b7e6b5 ("Remove fetch2 pipeline stage")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The tools complain about uart1_irq not being driven and not having a
default when HAS_UART1 is false. This sets it to 0 in that case.
Fixes: 7575b1e0c2 ("uart: Import and hook up opencore 16550 compatible UART")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
If BOOT_CLOCKS is false we currently get stuck in the flash
state machine. This patch from Ben fixes it.
Also fix an x state issue I see in icarus verilog where we need
to reset auto_state.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Some of the bits in the FPU buses end up as z state. Yosys
flags them, so we may as well clean it up.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Our flash controller fails when simulating with iverilog. Looking
closer, both wb_stash and auto_last_addr are X state, and things
fall apart after they get used.
Initialise them both fixes the iverilog issue.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Our Makefiles need some work, but for now create an FPGA target:
make FPGA_TARGET=verilator microwatt-verilator
ghdl and yosys can use containers using PODMAN=1 or DOCKER=1
options.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
yosys and verilator did not like us passing in the verilog and
exporting it again. Pass the source directly to verilator instead.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
When building with yosys we assume hello_world fits in 8kB. There's
enough free space that we can adjust the linker script to make it fit.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
This adds a test with a bdnzl followed immediately by a bdnz, to check
that CTR and LR both get evaluated and written back correctly in this
situation.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Random execution testcases showed that a bdnzl which doesn't branch,
followed immediately by a bdnz, uses the wrong value for CTR for the
bdnz. Decode2 detects the read-after-write hazard on CTR and tells
execute1 to use the bypass path. However, the bdnzl takes two cycles
because it has to write back both CTR and LR, meaning that by the time
the bdnz starts to execute, r.e.write_data no longer contains the CTR
value, but instead contains zero.
To fix this, we make execute1 maintain the written-back value of CTR
in r.e.write_data across the cycle where LR is written back (this is
possible because the LR writeback uses the exc_write_data path).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Branch instructions which do a redirect and write both CTR and LR were
not doing the write to LR due to a logic error. This fixes it.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
If an instruction fetch results in an instruction TLB miss, an
OP_FETCH_FAILED instruction is sent down the pipe. If the MSR[TE]
field is set for instruction tracing, the core currently considers
that executing the OP_FETCH_FAILED counts as having executed one
instruction and so generates a trace interrupt on the next valid
instruction, meaning that the trace interrupt happens before the
desired instruction rather than after it.
Fix this by not tracing OP_FETCH_FAILED instructions.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The masking enabled by opsel_amask is only used when rounding, to trim
the rounded result to the required precision. We now do the masking
after the adder rather than before (on the A input). This gives the
same result and helps timing. The path from r.shift through the mask
generator and adder to v.r was showing up as a critical path.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This moves longmask into the reg_type record, meaning that it now
needs to be decided a cycle earlier, in order to help timing.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This moves opsel_a into the reg_type record, meaning that the A
multiplexer input now needs to be decided a cycle earlier. This helps
timing by eliminating the combinatorial path from r.state and other
things to opsel_a and thence to in_a and result.
This means that some things now take an extra cycle, in particular
some of the exception cases such as when one or both operands are
NaNs. The NaN handling has been moved out to its own state, which
simplifies the logic for exception cases in other places. Additions
or subtractions where FRB's exponent is smaller than FRA's will
also take an extra cycle.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Anton Blanchard
Michael Neuling
Paul Mackerras