Instead of connecting core_alt_reset to litedram init_done, it moves to
a syscon register bit. This simplifies top- files and future soc_reset
handling. sdram main.c can unset the alt_reset bit after sdram init.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
It also stores the dirty status so that's known.
This does some Makefile tricks so that we only rebuild when the git
hash changes. This avoids rebuilding the world every time we run
make.
Also adds fusesoc generator, so that should continue to work as
before.
Signed-off-by: Dan Horák <dan@danny.cz>
Signed-off-by: Michael Neuling <mikey@neuling.org>
This makes the 64-bit wishbone buses have the address expressed in
units of doublewords (64 bits), and similarly for the 32-bit buses the
address is in units of words (32 bits). This is to comply with the
wishbone spec. Previously the addresses on the wishbone buses were in
units of bytes regardless of the bus data width, which is not correct
and caused problems with interfacing with externally-generated logic.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds litesdcard.v generated from the litex/litesdcard project,
along with logic in top-arty.vhdl to connect it into the system.
There is now a DMA wishbone coming in to soc.vhdl which is narrower
than the other wishbone masters (it has 32-bit data rather than
64-bit) so there is a widening/narrowing adapter between it and the
main wishbone master arbiter.
Also, litesdcard generates a non-pipelined wishbone for its DMA
connection, which needs to be converted to a pipelined wishbone. We
have a latch on both the incoming and outgoing sides of the wishbone
in order to help make timing (at the cost of two extra cycles of
latency).
litesdcard generates an interrupt signal which is wired up to input 3
of the ICS (IRQ 19).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a flag (currently not set) to indicate that the core is using
the architected timebase frequency of 512Mhz. When not set, the core is
using the proc frequency for the timebase.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This imports via fusesoc a 16550 compatible (ie "standard") UART,
and wires it up optionally in the SoC instead of the potato one.
This also adds support for a second UART (which is always a
16550) to Arty, wired to JC "bottom" port.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds an SPI flash controller which supports direct
memory-mapped access to the flash along with a manual
mode to send commands.
The direct mode can be set via generic to default to single
wire or quad mode. The controller supports normal, dual and quad
accesses with configurable commands, clock divider, dummy clocks
etc...
The SPI clock can be an even divider of sys_clk starting at 2
(so max 50Mhz with our typical Arty designs).
A flash offset is carried via generics to syscon to tell SW about
which portion of the flash is reserved for the FPGA bitfile. There
is currently no plumbing to make the CPU reset past that address (TBD).
Note: Operating at 50Mhz has proven unreliable without adding some
delay to the sampling of the input data. I'm working in improving
this, in the meantime, I'm leaving the default set at 25 Mhz.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds an option to disable the main BRAM and instead copy a
payload stashed along with the init code in the secondary BRAM
into DRAM and boot from there
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This changes the SoC interconnect such that the main 64-bit wishbone out
of the processor is first split between only 3 slaves (BRAM, DRAM and a
general "IO" bus) instead of all the slaves in the SoC.
The IO bus leg is then latched and down-converted to 32 bits data width,
before going through a second address decoder for the various IO devices.
This significantly reduces routing and timing pressure on the main bus,
allowing to get rid of frequent timing violations when synthetizing on
small'ish FPGAs such as the Artix-7 35T found on the original Arty board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These provides some info about the SoC (though it's still somewhat
incomplete and needs more work, see comments).
There's also a control register for selecting DRAM vs. BRAM at 0
(and for soft-resetting the SoC but that isn't wired up yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Matt Johnston
Paul Mackerras