This allows us to use the bypass at the input of execute1 for the
address and data operands for loadstore1.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This enables back-to-back execution of integer instructions where
the first instruction writes a GPR and the second reads the same
GPR. This is done with a set of multiplexers at the start of
execute1 which enable any of the three input operands to be taken
from the output of execute1 (i.e. r.e.write_data) rather than the
input from decode2 (i.e. e_in.read_data[123]).
This also requires changes to the hazard detection and handling.
Decode2 generates a signal indicating that the GPR being written
is available for bypass, which is true for instructions that are
executed in execute1 (rather than loadstore1/dcache). The
gpr_hazard module stores this "bypassable" bit, and if the same
GPR needs to be read by a subsequent instruction, it outputs a
"use_bypass" signal rather than generating a stall. The
use_bypass signal is then latched at the output of decode2 and
passed down to execute1 to control the input multiplexer.
At the moment there is no bypass on the inputs to loadstore1, but that
is OK because all load and store instructions are marked as
single-issue.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
For multiply and divide operations, execute1 now records the
destination GPR number, RC and OE from the instruction, and the
XER value. This means that the multiply and divide units don't
need to record those values and then send them back to execute1.
This makes the interface to those units a bit simpler. They
simply report an overflow signal along with the result value, and
execute1 takes care of updating XER if necessary.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With this, the divider is a unit that execute1 sends operands to and
which sends its results back to execute1, which then send them to
writeback. Execute1 now sends a stall signal when it gets a divide
or modulus instruction until it gets a valid signal back from the
divider. Divide and modulus instructions are no longer marked as
single-issue.
The data formatting step that used to be done in decode2 for div
and mod instructions is now done in execute1. We also do the
absolute value operation in that same cycle instead of taking an
extra cycle inside the divider for signed operations with a
negative operand.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With this, the multiplier isn't a separate pipe that decode2 issues
instructions to, but rather is a unit that execute1 sends operands
to and which sends the result back to execute1, which then sends it
to writeback. Execute1 now sends a stall signal when it gets a
multiply instruction until it gets a valid signal back from the
multiplier.
This all means that we no longer need to mark the multiply
instructions as single-issue.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This stores the most common SPRs in the register file.
This includes CTR and LR and a not yet final list of others.
The register file is set to 64 entries for now. Specific types
are defined that can represent a GPR index (gpr_index_t) or
a GPR/SPR index (gspr_index_t) along with conversion functions
between the two.
On order to deal with some forms of branch updating both LR and
CTR, we introduced a delayed update of LR after a branch link.
Note: We currently stall the pipeline on such a delayed branch,
but we could avoid stalling fetch in that specific case as we
know we have a branch delay. We could also limit that to the
specific case where we need to update both CTR and LR.
This allows us to make bcreg, mtspr and mfspr pipelined. decode1
will automatically force the single issue flag on mfspr/mtspr to
a "slow" SPR.
[paulus@ozlabs.org - fix direction of decode2.stall_in]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The carry is currently internal to execute1. We don't handle any of
the other XER fields.
This creates type called "xer_common_t" that contains the commonly
used XER bits (CA, CA32, SO, OV, OV32).
The value is stored in the CR file (though it could be a separate
module). The rest of the bits will be implemented as a separate
SPR and the two parts reconciled in mfspr/mtspr in latter commits.
We always read XER in decode2 (there is little point not to)
and send it down all pipeline branches as it will be needed in
writeback for all type of instructions when CR0:SO needs to be
updated (such forms exist for all pipeline branches even if we don't
yet implement them).
To avoid having to track XER hazards, we forward it back in EX1. This
assumes that other pipeline branches that can modify it (mult and div)
are running single issue for now.
One additional hazard to beware of is an XER:SO modifying instruction
in EX1 followed immediately by a store conditional. Due to our writeback
latency, the store will go down the LSU with the previous XER value,
thus the stcx. will set CR0:SO using an obsolete SO value.
I doubt there exist any code relying on this behaviour being correct
but we should account for it regardless, possibly by ensuring that
stcx. remain single issue initially, or later by adding some minimal
tracking or moving the LSU into the same pipeline as execute.
Missing some obscure XER affecting instructions like addex or mcrxrx.
[paulus@ozlabs.org - fix CA32 and OV32 for OP_ADD, fix order of
arguments to set_ov]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
To match our one stage execute.
This might change back if we end up adding 2 stages to match the
LSU, but in that case we'll want forwards as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This makes the exts[bhw] instructions do the sign extension in the
writeback stage using the sign-extension logic there instead of
having unique sign extension logic in execute1. This requires
passing the data length and sign extend flag from decode2 down
through execute1 and execute2 and into writeback. As a side bonus
we reduce the number of values in insn_type_t by two.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Check GPRs against any writers in the pipeline.
All instructions are still marked single in pipeline at
this stage.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
outstanding can only ever be -1 to 2 at the moment (0 or 1 on a
rising clock edge). Vivado is synthesizing a much wider adder
which is silly. Constrain it with a range statement. This should
be good for timing and saves us about 85 LUTs.
This will get relaxed when we add more pipelining, but only by a
few bits.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Consolidate and/andc/nand, or/orc/nor and xor/eqv, using a common
invert on the input and output. This saves us about 200 LUTs.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
This adds a new entity 'rotator' which contains combinatorial logic
for rotating and masking 64-bit values. It implements the operations
of the rlwinm, rlwnm, rlwimi, rldicl, rldicr, rldic, rldimi, rldcl,
rldcr, sld, slw, srd, srw, srad, sradi, sraw and srawi instructions.
It consists of a 3-stage 64-bit rotator using 4:1 multiplexors at
each stage, two mask generators, output logic and control logic.
The insn_type_t values used for these instructions have been reduced
to just 5: OP_RLC, OP_RLCL and OP_RLCR for the rotate and mask
instructions (clear both left and right, clear left, clear right
variants), OP_SHL for left shifts, and OP_SHR for right shifts.
The control signals for the rotator are derived from the opcode
and from the is_32bit and is_signed fields of the decode_rom_t.
The rotator is instantiated as an entity in execute1 so that we can
be sure we only have one of it.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This changes the names of the mul_32bit and mul_signed fields of
decode_rom_t to is_32bit and is_signed, so they can be used with
other types of operations besides multiplies.
This plumbs the is_32bit and is_signed flags down into execute1,
though they are not used at this point.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This aims to simplify the logic between the instruction image and
the register file read address ports and reduce the size of the decode
tables. With this patch, the input_reg_a column of the decode tables
can only select RA or zeroes, the input_reg_b column can only select
RB or a constant (0, -1, or an immediate value from the instruction),
and the input_reg_c columns can only select RS or zeroes.
That means that the rotate/shift/logical ops now have their first
input coming in via the input_reg_c column. That means we need to
add a read_data3 field to the Decode2ToExecuteType record, but that
will go away again when we split out the rotate/mask/logical ops to
their own unit.
As a related but not tightly connected change, this patch also sets
the read1_enable signal to the register file be 0 when RA=0 and the
input_reg_a for the instruction is RA_OR_ZERO (previously it was 1).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
All of the PPC add and subtract instructions, including carrying
and extended versions, do much the same arithmetic operation:
result = (I xor A) + B + C
where A is the value from RA, I provides a logical inversion of A
(i.e. I is 0 or -1), B is either from RB or is a constant 0 or -1,
and C is 0, 1 or the carry bit from XER (CA).
To consolidate all the add/subtract instructions into a single
OP_ADD, we add a column to decode_rom_t to indicate when A should
be inverted, and change the input_carry field to a 3-state selector
to select C in the equation above.
This also adds a new "CONST_M1" value for input_reg_b_t to indicate
that B is a constant -1. This allows us to implement addme and
subfme.
The addex instruction appears not to exist, so the comments referring
to it are removed.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The const* fields of decode_rom_t drove multiplexers in decode2 that
picked out various instruction fields and put them into the const*
fields of the Decode2ToExecute1Type record, from where they were
used in execute1. However, the code in execute1 can just as easily
use the appropriate fields of the original instruction word, since
that is now available in execute1. This therefore changes the
code to do that, resulting in smaller decode tables.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Instead of doing mfctr, mflr, mftb, mtctr, mtlr as separate ops,
just pass down mfspr and mtspr ops with the spr number and let
execute1 decode which SPR we're addressing. This will help reduce
the number of instruction bits decode1 needs to look at.
In fact we now pass down the whole instruction from decode2 to
execute1. We will need more bits of the instruction in future,
and the tools should just optimize away any that we don't end
up using. Since the 'aa' bit was just a copy of an instruction
bit, we can now remove it from the record.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Hopefully it's not too timing catastrophic. The variable newcrf will
be handy for the other CR ops when we implement them I suspect.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves the negation of negative operands for signed divide and
modulus operations out of the decode2 stage and into the divider.
If either of the operands for a signed divide or modulus operation
is negative, the divider now takes an extra cycle to negate the
operands that are negative.
The interface to the divider now has an 'is_signed' signal rather
than a 'neg_result' signal, and the dividend and divisor can be
negative, so divider_tb had to be updated for the new interface.
The reason for doing this is that one of the worst timing violations
on the Arty A7-100 at 100MHz involved the carry chain in the adders
that did the negation of the dividend and divisor in the decode stage.
Moving the negations to a separate cycle fixes that and also seems to
reduce the total number of slice LUTs used.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a divider unit, connected to the core in much the same way
that the multiplier unit is connected. The division algorithm is
very simple-minded, taking 64 clock cycles for any division (even
32-bit division instructions).
The decoding is simplified by making use of regularities in the
instruction encoding for div* and mod* instructions. Instead of
having PPC_* encodings from the first-stage decoder for each of the
different div* and mod* instructions, we now just have PPC_DIV and
PPC_MOD, and the inputs to the divider that indicate what sort of
division operation to do are derived from instruction word bits.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This module adds some simple core controls:
reset, stop, start, step
along with icache clear and reading the NIA and core
status bits
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org
Right now we continually print all 3 possible GPRs an instruction
may be using. Add signals so we only print GPRs when they are
actually read. This should hopefully optimise away when synthesized.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Handle the CR as a single field with per nibble enables. Forward any
writes in the same cycle.
If this proves to be an issue for timing, we may want to revisit
this in the future. For now, it keeps things simple.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
The decode2 stage was spaghetti code and needed cleaning up.
Create a series of functions to pull fields from a ppc instruction
and also a series of helpers to extract values for the execution
units.
As suggested by Paul, we should pass all signals to the execution
units and only set the valid signal conditionally, which should
use less resources.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Anton Blanchard
Paul Mackerras