Commit Graph

8 Commits (76f61ef823f03349d4a41791b9c2840259eb3009)

Author SHA1 Message Date
Anton Blanchard ebdddcc402 Remove some FPGA style signal inits
These don't work on the ASIC flow, so remove them and initialise
them explicitly where required.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
2 years ago
Anton Blanchard a750365ffa Remove some FPGA style signal inits
These don't work on the ASIC flow, so remove them and initialise
them explicitly where required.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
2 years ago
Paul Mackerras ca4eb46aea Make wishbone addresses be in units of doublewords or words
This makes the 64-bit wishbone buses have the address expressed in
units of doublewords (64 bits), and similarly for the 32-bit buses the
address is in units of words (32 bits).  This is to comply with the
wishbone spec.  Previously the addresses on the wishbone buses were in
units of bytes regardless of the bus data width, which is not correct
and caused problems with interfacing with externally-generated logic.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
Anton Blanchard af462f0ca9 Reformat spi_flash_ctrl
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
3 years ago
Anton Blanchard c870040a20 Fix an issue in flash controller when BOOT_CLOCKS is false
If BOOT_CLOCKS is false we currently get stuck in the flash
state machine. This patch from Ben fixes it.

Also fix an x state issue I see in icarus verilog where we need
to reset auto_state.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
3 years ago
Anton Blanchard 7c8bc85e44 Fix a few reset issues in flash controller
Our flash controller fails when simulating with iverilog. Looking
closer, both wb_stash and auto_last_addr are X state, and things
fall apart after they get used.

Initialise them both fixes the iverilog issue.

Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
3 years ago
Benjamin Herrenschmidt 3c2739e10a spi: Send dummy clocks at boot
When using an FPGA which routes the SPI clock via STARTUPE2 as is
done on the Nexys Video (or optionally on Arty), the HW needs at
least 3 beats of that clock to complete the switch from the internal
config clock to the one we provide.

This works around it by having the SPI controller send 8 dummy
clocks at boot time with CS held high.

Without this, flash identification will fail those boards

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago
Benjamin Herrenschmidt cc4dcb3597 spi: Add SPI Flash controller
This adds an SPI flash controller which supports direct
memory-mapped access to the flash along with a manual
mode to send commands.

The direct mode can be set via generic to default to single
wire or quad mode. The controller supports normal, dual and quad
accesses with configurable commands, clock divider, dummy clocks
etc...

The SPI clock can be an even divider of sys_clk starting at 2
(so max 50Mhz with our typical Arty designs).

A flash offset is carried via generics to syscon to tell SW about
which portion of the flash is reserved for the FPGA bitfile. There
is currently no plumbing to make the CPU reset past that address (TBD).

Note: Operating at 50Mhz has proven unreliable without adding some
delay to the sampling of the input data. I'm working in improving
this, in the meantime, I'm leaving the default set at 25 Mhz.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
4 years ago