This makes the control bus currently going out of "soc" towards
litedram more generic for external IO devices added by the
top-level rather than inside the SoC proper.
This is mostly renaming of signals and a small change on how the
address decoder operates, using a separate "cascaded" decode for
the external IOs.
We make the region 0xc8nn_nnnn be the "external IO" region for
now.
This will make it easier / cleaner to add more external devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds an SPI flash controller which supports direct
memory-mapped access to the flash along with a manual
mode to send commands.
The direct mode can be set via generic to default to single
wire or quad mode. The controller supports normal, dual and quad
accesses with configurable commands, clock divider, dummy clocks
etc...
The SPI clock can be an even divider of sys_clk starting at 2
(so max 50Mhz with our typical Arty designs).
A flash offset is carried via generics to syscon to tell SW about
which portion of the flash is reserved for the FPGA bitfile. There
is currently no plumbing to make the CPU reset past that address (TBD).
Note: Operating at 50Mhz has proven unreliable without adding some
delay to the sampling of the input data. I'm working in improving
this, in the meantime, I'm leaving the default set at 25 Mhz.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We still had some wires bringing an extra serial port out of
litedram for the built-in riscv processor. This is all gone now
so take them out.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds an option to disable the main BRAM and instead copy a
payload stashed along with the init code in the secondary BRAM
into DRAM and boot from there
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This changes the SoC interconnect such that the main 64-bit wishbone out
of the processor is first split between only 3 slaves (BRAM, DRAM and a
general "IO" bus) instead of all the slaves in the SoC.
The IO bus leg is then latched and down-converted to 32 bits data width,
before going through a second address decoder for the various IO devices.
This significantly reduces routing and timing pressure on the main bus,
allowing to get rid of frequent timing violations when synthetizing on
small'ish FPGAs such as the Artix-7 35T found on the original Arty board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When using litedram, request a much longer PLL reset. This seems to
help get rid of all the grabled output after config.
Also use the clean system_rst out of litedram as our source of reset
for the rest of the SoC (it is synchronized with system_clk and takes
pll_locked into account already)
Things have changed a bit in upstream LiteX. LiteDRAM now exposes a
wishbone for the CSRs for example.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These provides some info about the SoC (though it's still somewhat
incomplete and needs more work, see comments).
There's also a control register for selecting DRAM vs. BRAM at 0
(and for soft-resetting the SoC but that isn't wired up yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The old toplevel.vhdl becomes top-generic.vhdl, which is to be used
by platforms that do not have a litedram option.
Arty has its own top-arty.vhdl which supports litedram and is now
hooked up
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt