Merge pull request #364 from shenki/readme-updates

Readme updates
pull/187/merge
Michael Neuling 2 years ago committed by GitHub
commit ee5e3778ed
No known key found for this signature in database
GPG Key ID: 4AEE18F83AFDEB23

@ -103,14 +103,8 @@ sudo dnf install fusesoc


``` ```
fusesoc init fusesoc init
``` fusesoc fetch uart16550

fusesoc library add microwatt /path/to/microwatt
- Create a working directory and point FuseSoC at microwatt:

```
mkdir microwatt-fusesoc
cd microwatt-fusesoc
fusesoc library add microwatt /path/to/microwatt/
``` ```


- Build using FuseSoC. For hello world (Replace nexys_video with your FPGA board such as --target=arty_a7-100): - Build using FuseSoC. For hello world (Replace nexys_video with your FPGA board such as --target=arty_a7-100):
@ -128,6 +122,68 @@ You should then be able to see output via the serial port of the board (/dev/tty
fusesoc run --target=nexys_video microwatt fusesoc run --target=nexys_video microwatt
``` ```


## Linux on Microwatt

Mainline Linux supports Microwatt as of v5.14. The Arty A7 is the best tested
platform, but it's also been tested on the OrangeCrab and ButterStick.

1. Use buildroot to create a userspace

A small change is required to glibc in order to support the VMX/AltiVec-less
Microwatt, as float128 support is mandiatory and for this in GCC requires
VSX/AltiVec. This change is included in Joel's buildroot fork, along with a
defconfig:
```
git clone -b microwatt https://github.com/shenki/buildroot
cd buildroot
make ppc64le_microwatt_defconfig
make
```

The output is `output/images/rootfs.cpio`.

2. Build the Linux kernel
```
git clone https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
cd linux
make ARCH=powerpc microwatt_defconfig
make ARCH=powerpc CROSS_COMPILE=powerpc64le-linux-gnu- \
CONFIG_INITRAMFS_SOURCE=/buildroot/output/images/rootfs.cpio -j`nproc`
```

The output is `arch/powerpc/boot/dtbImage.microwatt.elf`.

3. Build gateware using FuseSoC

First configure FuseSoC as above.
```
fusesoc run --build --target=arty_a7-100 microwatt --no_bram --memory_size=0
```

The output is `build/microwatt_0/arty_a7-100-vivado/microwatt_0.bit`.

4. Program the flash

This operation will overwrite the contents of your flash.

For the Arty A7 A100, set `FLASH_ADDRESS` to `0x400000` and pass `-f a100`.

For the Arty A7 A35, set `FLASH_ADDRESS` to `0x300000` and pass `-f a35`.
```
microwatt/openocd/flash-arty -f a100 build/microwatt_0/arty_a7-100-vivado/microwatt_0.bit
microwatt/openocd/flash-arty -f a100 dtbImage.microwatt.elf -t bin -a $FLASH_ADDRESS
```

5. Connect to the second USB TTY device exposed by the FPGA

```
minicom -D /dev/ttyUSB1
```

The gateware has firmware that will look at `FLASH_ADDRESS` and attempt to
parse an ELF there, loading it to the address specified in the ELF header
and jumping to it.

## Testing ## Testing


- A simple test suite containing random execution test cases and a couple of - A simple test suite containing random execution test cases and a couple of

Loading…
Cancel
Save