loadstore1: Generate busy signal earlier

This makes the calculation of busy as simple as possible and dependent
only on register outputs.  The timing of busy is critical, as it gates
the valid signal for the next instruction, and therefore any delays
in dropping busy at the end of a load or store directly impact the
timing of a host of other paths.

This also separates the 'done without error' and 'done with error'
cases from the MMU into separate signals that are both driven directly
from registers.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

common.vhdl

@@ -315,6 +315,7 @@ package common is
 
     type MmuToLoadstore1Type is record
         done       : std_ulogic;
+        err        : std_ulogic;
         invalid    : std_ulogic;
         badtree    : std_ulogic;
         segerr     : std_ulogic;

loadstore1.vhdl

@@ -80,6 +80,9 @@ architecture behave of loadstore1 is
         dsisr        : std_ulogic_vector(31 downto 0);
         instr_fault  : std_ulogic;
         sprval       : std_ulogic_vector(63 downto 0);
+        busy         : std_ulogic;
+        wait_dcache  : std_ulogic;
+        wait_mmu     : std_ulogic;
     end record;
 
     type byte_sel_t is array(0 to 7) of std_ulogic;
@@ -128,6 +131,9 @@ begin
         if rising_edge(clk) then
             if rst = '1' then
                 r.state <= IDLE;
+                r.busy <= '0';
+                r.wait_dcache <= '0';
+                r.wait_mmu <= '0';
             else
                 r <= rin;
             end if;
@@ -228,8 +234,17 @@ begin
         -- compute (addr + 8) & ~7 for the second doubleword when unaligned
         next_addr := std_ulogic_vector(unsigned(r.addr(63 downto 3)) + 1) & "000";
 
+        -- Busy calculation.
+        -- We need to minimize the delay from clock to busy valid because it
+        -- gates the start of execution of the next instruction.
+        busy := r.busy or (r.wait_dcache and not d_in.valid) or (r.wait_mmu and not m_in.done);
+
         done := '0';
+        if r.state /= IDLE and busy = '0' then
+            done := '1';
+        end if;
         exception := '0';
+
         case r.state is
         when IDLE =>
 
@@ -255,7 +270,6 @@ begin
                     dsisr(63 - 38) := not r.load;
                     -- XXX there is no architected bit for this
                     dsisr(63 - 35) := d_in.cache_paradox;
-                    v.state := IDLE;
                 else
                     -- Look up the translation for TLB miss
                     -- and also for permission error and RC error
@@ -279,8 +293,6 @@ begin
                     else
                         -- stores write back rA update in this cycle
                         do_update := r.update;
-                        done := '1';
-                        v.state := IDLE;
                     end if;
                 end if;
             end if;
@@ -294,8 +306,6 @@ begin
                 byte_sel := r.first_bytes;
             end if;
             if m_in.done = '1' then
-                if m_in.invalid = '0' and m_in.perm_error = '0' and m_in.rc_error = '0' and
-                    m_in.badtree = '0' and m_in.segerr = '0' then
                 if r.instr_fault = '0' then
                     -- retry the request now that the MMU has installed a TLB entry
                     req := '1';
@@ -304,43 +314,28 @@ begin
                     else
                         v.state := ACK_WAIT;
                     end if;
-                    else
-                        -- nothing to do, the icache retries automatically
-                        done := '1';
-                        v.state := IDLE;
                 end if;
-                else
+            end if;
+            if m_in.err = '1' then
                 exception := '1';
                 dsisr(63 - 33) := m_in.invalid;
                 dsisr(63 - 36) := m_in.perm_error;
                 dsisr(63 - 38) := not r.load;
                 dsisr(63 - 44) := m_in.badtree;
                 dsisr(63 - 45) := m_in.rc_error;
-                    v.state := IDLE;
-                end if;
             end if;
 
         when TLBIE_WAIT =>
-            if m_in.done = '1' then
-                -- tlbie is finished
-                done := '1';
-                v.state := IDLE;
-            end if;
 
         when LD_UPDATE =>
             do_update := '1';
-            v.state := IDLE;
-            done := '1';
 
         when SPR_CMPLT =>
-            done := '1';
-            v.state := IDLE;
 
         end case;
 
-        busy := '1';
-        if r.state = IDLE or done = '1' then
-            busy := '0';
+        if done = '1' or exception = '1' then
+            v.state := IDLE;
         end if;
 
         -- Note that l_in.valid is gated with busy inside execute1
@@ -450,6 +445,31 @@ begin
             end if;
         end if;
 
+        -- Work out whether we'll be busy next cycle
+        v.busy := '0';
+        v.wait_dcache := '0';
+        v.wait_mmu := '0';
+        case v.state is
+            when SECOND_REQ =>
+                v.busy := '1';
+            when ACK_WAIT =>
+                if v.last_dword = '0' or (v.load = '1' and v.update = '1') then
+                    v.busy := '1';
+                else
+                    v.wait_dcache := '1';
+                end if;
+            when MMU_LOOKUP =>
+                if v.instr_fault = '0' then
+                    v.busy := '1';
+                else
+                    v.wait_mmu := '1';
+                end if;
+            when TLBIE_WAIT =>
+                v.wait_mmu := '1';
+            when others =>
+                -- not busy next cycle
+        end case;
+
         -- Update outputs to dcache
         d_out.valid <= req;
         d_out.load <= v.load;

mmu.vhdl

@@ -52,6 +52,7 @@ architecture behave of mmu is
         -- internal state
         state     : state_t;
         done      : std_ulogic;
+        err       : std_ulogic;
         pgtbl0    : std_ulogic_vector(63 downto 0);
         pt0_valid : std_ulogic;
         pgtbl3    : std_ulogic_vector(63 downto 0);
@@ -92,7 +93,10 @@ begin
                     report "MMU got tlb miss for " & to_hstring(rin.addr);
                 end if;
                 if l_out.done = '1' then
-                    report "MMU completing op with invalid=" & std_ulogic'image(l_out.invalid) &
+                    report "MMU completing op without error";
+                end if;
+                if l_out.err = '1' then
+                    report "MMU completing op with err invalid=" & std_ulogic'image(l_out.invalid) &
                         " badtree=" & std_ulogic'image(l_out.badtree);
                 end if;
                 if rin.state = RADIX_LOOKUP then
@@ -200,6 +204,7 @@ begin
         v.valid := '0';
         dcreq := '0';
         v.done := '0';
+        v.err := '0';
         v.invalid := '0';
         v.badtree := '0';
         v.segerror := '0';
@@ -412,7 +417,8 @@ begin
         end case;
 
         if v.state = RADIX_FINISH or (v.state = RADIX_LOAD_TLB and r.iside = '1') then
-            v.done := '1';
+            v.err := v.invalid or v.badtree or v.segerror or v.perm_err or v.rc_error;
+            v.done := not v.err;
         end if;
 
         if r.addr(63) = '1' then
@@ -451,6 +457,7 @@ begin
         end if;
 
         l_out.done <= r.done;
+        l_out.err <= r.err;
         l_out.invalid <= r.invalid;
         l_out.badtree <= r.badtree;
         l_out.segerr <= r.segerror;