|
|
|
library ieee;
|
|
|
|
use ieee.std_logic_1164.all;
|
|
|
|
use ieee.numeric_std.all;
|
|
|
|
|
|
|
|
library work;
|
|
|
|
use work.common.all;
|
|
|
|
use work.decode_types.all;
|
|
|
|
use work.insn_helpers.all;
|
|
|
|
|
|
|
|
entity decode1 is
|
|
|
|
generic (
|
|
|
|
HAS_FPU : boolean := true;
|
|
|
|
-- Non-zero to enable log data collection
|
|
|
|
LOG_LENGTH : natural := 0
|
|
|
|
);
|
|
|
|
port (
|
|
|
|
clk : in std_ulogic;
|
|
|
|
rst : in std_ulogic;
|
|
|
|
|
|
|
|
stall_in : in std_ulogic;
|
|
|
|
flush_in : in std_ulogic;
|
|
|
|
busy_out : out std_ulogic;
|
|
|
|
flush_out : out std_ulogic;
|
|
|
|
|
|
|
|
f_in : in IcacheToDecode1Type;
|
|
|
|
f_out : out Decode1ToFetch1Type;
|
|
|
|
d_out : out Decode1ToDecode2Type;
|
|
|
|
r_out : out Decode1ToRegisterFileType;
|
|
|
|
log_out : out std_ulogic_vector(12 downto 0)
|
|
|
|
);
|
|
|
|
end entity decode1;
|
|
|
|
|
|
|
|
architecture behaviour of decode1 is
|
|
|
|
signal r, rin : Decode1ToDecode2Type;
|
|
|
|
signal f, fin : Decode1ToFetch1Type;
|
|
|
|
|
|
|
|
type br_predictor_t is record
|
|
|
|
br_target : signed(61 downto 0);
|
|
|
|
predict : std_ulogic;
|
|
|
|
end record;
|
|
|
|
|
|
|
|
signal br, br_in : br_predictor_t;
|
|
|
|
|
|
|
|
signal decode_rom_addr : insn_code;
|
|
|
|
signal decode : decode_rom_t;
|
|
|
|
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
type prefix_state_t is record
|
|
|
|
prefixed : std_ulogic;
|
|
|
|
prefix : std_ulogic_vector(25 downto 0);
|
|
|
|
pref_ia : std_ulogic_vector(3 downto 0);
|
|
|
|
end record;
|
|
|
|
constant prefix_state_init : prefix_state_t := (prefixed => '0', prefix => (others => '0'),
|
|
|
|
pref_ia => (others => '0'));
|
|
|
|
|
|
|
|
signal pr, pr_in : prefix_state_t;
|
|
|
|
|
|
|
|
signal fetch_failed : std_ulogic;
|
|
|
|
|
|
|
|
-- If we have an FPU, then it is used for integer divisions,
|
|
|
|
-- otherwise a dedicated divider in the ALU is used.
|
|
|
|
function divider_unit(hf : boolean) return unit_t is
|
|
|
|
begin
|
|
|
|
if hf then
|
|
|
|
return FPU;
|
|
|
|
else
|
|
|
|
return ALU;
|
|
|
|
end if;
|
|
|
|
end;
|
|
|
|
constant DVU : unit_t := divider_unit(HAS_FPU);
|
|
|
|
|
|
|
|
type decoder_rom_t is array(insn_code) of decode_rom_t;
|
|
|
|
|
|
|
|
constant decode_rom : decoder_rom_t := (
|
|
|
|
-- unit fac internal in1 in2 in3 out CR CR inv inv cry cry ldst BR sgn upd rsrv 32b sgn rc lk sgl rpt
|
|
|
|
-- op in out A out in out len ext pipe
|
|
|
|
INSN_illegal => (ALU, NONE, OP_ILLEGAL, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_fetch_fail => (LDST, NONE, OP_FETCH_FAILED, CIA, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
|
|
|
|
INSN_add => (ALU, NONE, OP_ADD, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_addc => (ALU, NONE, OP_ADD, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '1', NONE, '0', '0', '0', '0', '0', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_adde => (ALU, NONE, OP_ADD, RA, RB, NONE, RT, '0', '0', '0', '0', CA, '1', NONE, '0', '0', '0', '0', '0', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_addex => (ALU, NONE, OP_ADD, RA, RB, NONE, RT, '0', '0', '0', '0', OV, '1', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_addg6s => (ALU, NONE, OP_ADDG6S, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_addi => (ALU, NONE, OP_ADD, RA_OR_ZERO, CONST_SI, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_addic => (ALU, NONE, OP_ADD, RA, CONST_SI, NONE, RT, '0', '0', '0', '0', ZERO, '1', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_addic_dot => (ALU, NONE, OP_ADD, RA, CONST_SI, NONE, RT, '0', '0', '0', '0', ZERO, '1', NONE, '0', '0', '0', '0', '0', '0', ONE, '0', '0', NONE),
|
|
|
|
INSN_addis => (ALU, NONE, OP_ADD, RA_OR_ZERO, CONST_SI_HI, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_addme => (ALU, NONE, OP_ADD, RA, CONST_M1, NONE, RT, '0', '0', '0', '0', CA, '1', NONE, '0', '0', '0', '0', '0', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_addpcis => (ALU, NONE, OP_ADD, CIA, CONST_DXHI4, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_addze => (ALU, NONE, OP_ADD, RA, NONE, NONE, RT, '0', '0', '0', '0', CA, '1', NONE, '0', '0', '0', '0', '0', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_and => (ALU, NONE, OP_LOGIC, NONE, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_andc => (ALU, NONE, OP_LOGIC, NONE, RB, RS, RA, '0', '0', '1', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_andi_dot => (ALU, NONE, OP_LOGIC, NONE, CONST_UI, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', ONE, '0', '0', NONE),
|
|
|
|
INSN_andis_dot => (ALU, NONE, OP_LOGIC, NONE, CONST_UI_HI, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', ONE, '0', '0', NONE),
|
|
|
|
INSN_attn => (ALU, NONE, OP_ATTN, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '1', NONE),
|
|
|
|
INSN_brel => (ALU, NONE, OP_B, CIA, CONST_LI, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '1', '0', NONE),
|
|
|
|
INSN_babs => (ALU, NONE, OP_B, NONE, CONST_LI, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '1', '0', NONE),
|
|
|
|
INSN_bcrel => (ALU, NONE, OP_BC, CIA, CONST_BD, NONE, NONE, '1', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '1', '0', NONE),
|
|
|
|
INSN_bcabs => (ALU, NONE, OP_BC, NONE, CONST_BD, NONE, NONE, '1', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '1', '0', NONE),
|
|
|
|
INSN_bcctr => (ALU, NONE, OP_BCREG, NONE, NONE, NONE, NONE, '1', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '1', '0', NONE),
|
|
|
|
INSN_bclr => (ALU, NONE, OP_BCREG, NONE, NONE, NONE, NONE, '1', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '1', '0', NONE),
|
|
|
|
INSN_bctar => (ALU, NONE, OP_BCREG, NONE, NONE, NONE, NONE, '1', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '1', '0', NONE),
|
|
|
|
INSN_bperm => (ALU, NONE, OP_BPERM, NONE, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_brh => (ALU, NONE, OP_BREV, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_brw => (ALU, NONE, OP_BREV, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_brd => (ALU, NONE, OP_BREV, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_cbcdtd => (ALU, NONE, OP_BCD, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_cdtbcd => (ALU, NONE, OP_BCD, NONE, NONE, RS, RA, '0', '0', '1', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_cmp => (ALU, NONE, OP_CMP, RA, RB, NONE, NONE, '0', '1', '1', '0', ONE, '0', NONE, '0', '0', '0', '0', '0', '1', NONE, '0', '0', NONE),
|
|
|
|
INSN_cmpb => (ALU, NONE, OP_CMPB, NONE, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_cmpeqb => (ALU, NONE, OP_CMPEQB, RA, RB, NONE, NONE, '0', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_cmpi => (ALU, NONE, OP_CMP, RA, CONST_SI, NONE, NONE, '0', '1', '1', '0', ONE, '0', NONE, '0', '0', '0', '0', '0', '1', NONE, '0', '0', NONE),
|
|
|
|
INSN_cmpl => (ALU, NONE, OP_CMP, RA, RB, NONE, NONE, '0', '1', '1', '0', ONE, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_cmpli => (ALU, NONE, OP_CMP, RA, CONST_UI, NONE, NONE, '0', '1', '1', '0', ONE, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_cmprb => (ALU, NONE, OP_CMPRB, RA, RB, NONE, NONE, '0', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_cntlzd => (ALU, NONE, OP_CNTZ, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_cntlzw => (ALU, NONE, OP_CNTZ, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_cnttzd => (ALU, NONE, OP_CNTZ, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_cnttzw => (ALU, NONE, OP_CNTZ, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_crand => (ALU, NONE, OP_CROP, NONE, NONE, NONE, NONE, '1', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_crandc => (ALU, NONE, OP_CROP, NONE, NONE, NONE, NONE, '1', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_creqv => (ALU, NONE, OP_CROP, NONE, NONE, NONE, NONE, '1', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_crnand => (ALU, NONE, OP_CROP, NONE, NONE, NONE, NONE, '1', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_crnor => (ALU, NONE, OP_CROP, NONE, NONE, NONE, NONE, '1', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_cror => (ALU, NONE, OP_CROP, NONE, NONE, NONE, NONE, '1', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_crorc => (ALU, NONE, OP_CROP, NONE, NONE, NONE, NONE, '1', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_crxor => (ALU, NONE, OP_CROP, NONE, NONE, NONE, NONE, '1', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_darn => (ALU, NONE, OP_DARN, NONE, NONE, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_dcbf => (ALU, NONE, OP_DCBF, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_dcbst => (ALU, NONE, OP_DCBST, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_dcbt => (ALU, NONE, OP_DCBT, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_dcbtst => (ALU, NONE, OP_DCBTST, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_dcbz => (LDST, NONE, OP_DCBZ, RA_OR_ZERO, RB, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_divd => (DVU, NONE, OP_DIV, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '1', RCOE, '0', '0', NONE),
|
|
|
|
INSN_divde => (DVU, NONE, OP_DIVE, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '1', RCOE, '0', '0', NONE),
|
|
|
|
INSN_divdeu => (DVU, NONE, OP_DIVE, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_divdu => (DVU, NONE, OP_DIV, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_divw => (DVU, NONE, OP_DIV, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '1', RCOE, '0', '0', NONE),
|
|
|
|
INSN_divwe => (DVU, NONE, OP_DIVE, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '1', RCOE, '0', '0', NONE),
|
|
|
|
INSN_divweu => (DVU, NONE, OP_DIVE, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_divwu => (DVU, NONE, OP_DIV, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_eieio => (ALU, NONE, OP_NOP, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_eqv => (ALU, NONE, OP_XOR, NONE, RB, RS, RA, '0', '0', '0', '1', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_extsb => (ALU, NONE, OP_EXTS, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_extsh => (ALU, NONE, OP_EXTS, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_extsw => (ALU, NONE, OP_EXTS, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_extswsli => (ALU, NONE, OP_EXTSWSLI, NONE, CONST_SH, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fabs => (FPU, FPU, OP_FP_MOVE, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fadd => (FPU, FPU, OP_FP_ARITH, FRA, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fadds => (FPU, FPU, OP_FP_ARITH, FRA, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fcfid => (FPU, FPU, OP_FP_MISC, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fcfids => (FPU, FPU, OP_FP_MISC, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fcfidu => (FPU, FPU, OP_FP_MISC, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fcfidus => (FPU, FPU, OP_FP_MISC, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fcmpo => (FPU, FPU, OP_FP_CMP, FRA, FRB, NONE, NONE, '0', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_fcmpu => (FPU, FPU, OP_FP_CMP, FRA, FRB, NONE, NONE, '0', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_fcpsgn => (FPU, FPU, OP_FP_MOVE, FRA, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fctid => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fctidu => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fctiduz => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fctidz => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fctiw => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fctiwu => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fctiwuz => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fctiwz => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fdiv => (FPU, FPU, OP_FP_ARITH, FRA, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fdivs => (FPU, FPU, OP_FP_ARITH, FRA, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fmadd => (FPU, FPU, OP_FP_ARITH, FRA, FRB, FRC, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fmadds => (FPU, FPU, OP_FP_ARITH, FRA, FRB, FRC, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fmr => (FPU, FPU, OP_FP_MOVE, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fmrgew => (FPU, FPU, OP_FP_MISC, FRA, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_fmrgow => (FPU, FPU, OP_FP_MISC, FRA, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_fmsub => (FPU, FPU, OP_FP_ARITH, FRA, FRB, FRC, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fmsubs => (FPU, FPU, OP_FP_ARITH, FRA, FRB, FRC, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fmul => (FPU, FPU, OP_FP_ARITH, FRA, NONE, FRC, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fmuls => (FPU, FPU, OP_FP_ARITH, FRA, NONE, FRC, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fnabs => (FPU, FPU, OP_FP_MOVE, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fneg => (FPU, FPU, OP_FP_MOVE, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fnmadd => (FPU, FPU, OP_FP_ARITH, FRA, FRB, FRC, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fnmadds => (FPU, FPU, OP_FP_ARITH, FRA, FRB, FRC, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fnmsub => (FPU, FPU, OP_FP_ARITH, FRA, FRB, FRC, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fnmsubs => (FPU, FPU, OP_FP_ARITH, FRA, FRB, FRC, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fre => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fres => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_frim => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_frin => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_frip => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_friz => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_frsp => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_frsqrte => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_frsqrtes => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fsel => (FPU, FPU, OP_FP_MOVE, FRA, FRB, FRC, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fsqrt => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fsqrts => (FPU, FPU, OP_FP_ARITH, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fsub => (FPU, FPU, OP_FP_ARITH, FRA, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_fsubs => (FPU, FPU, OP_FP_ARITH, FRA, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_ftdiv => (FPU, FPU, OP_FP_CMP, FRA, FRB, NONE, NONE, '0', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_ftsqrt => (FPU, FPU, OP_FP_CMP, NONE, FRB, NONE, NONE, '0', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_icbi => (ALU, NONE, OP_ICBI, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '1', NONE),
|
|
|
|
INSN_icbt => (ALU, NONE, OP_ICBT, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '1', NONE),
|
|
|
|
INSN_isel => (ALU, NONE, OP_ISEL, RA_OR_ZERO, RB, NONE, RT, '1', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_isync => (ALU, NONE, OP_ISYNC, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lbarx => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '0', '1', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lbz => (LDST, NONE, OP_LOAD, RA_OR_ZERO, CONST_SI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lbzcix => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '1', '0', ZERO, '0', is1B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lbzu => (LDST, NONE, OP_LOAD, RA_OR_ZERO, CONST_SI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_lbzux => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_lbzx => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_ld => (LDST, NONE, OP_LOAD, RA_OR_ZERO, CONST_DS, NONE, RT, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_ldarx => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '1', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_ldbrx => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is8B, '1', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_ldcix => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '1', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_ldu => (LDST, NONE, OP_LOAD, RA_OR_ZERO, CONST_DS, NONE, RT, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_ldux => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_ldx => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lfd => (LDST, FPU, OP_LOAD, RA_OR_ZERO, CONST_SI, NONE, FRT, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lfdu => (LDST, FPU, OP_LOAD, RA_OR_ZERO, CONST_SI, NONE, FRT, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_lfdux => (LDST, FPU, OP_LOAD, RA_OR_ZERO, RB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_lfdx => (LDST, FPU, OP_LOAD, RA_OR_ZERO, RB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lfiwax => (LDST, FPU, OP_LOAD, RA_OR_ZERO, RB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '1', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lfiwzx => (LDST, FPU, OP_LOAD, RA_OR_ZERO, RB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lfs => (LDST, FPU, OP_LOAD, RA_OR_ZERO, CONST_SI, NONE, FRT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '1', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lfsu => (LDST, FPU, OP_LOAD, RA_OR_ZERO, CONST_SI, NONE, FRT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '1', '0', '1', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_lfsux => (LDST, FPU, OP_LOAD, RA_OR_ZERO, RB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '1', '0', '1', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_lfsx => (LDST, FPU, OP_LOAD, RA_OR_ZERO, RB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '1', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lha => (LDST, NONE, OP_LOAD, RA_OR_ZERO, CONST_SI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is2B, '0', '1', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lharx => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '0', '1', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lhau => (LDST, NONE, OP_LOAD, RA_OR_ZERO, CONST_SI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is2B, '0', '1', '1', '0', '0', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_lhaux => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is2B, '0', '1', '1', '0', '0', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_lhax => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is2B, '0', '1', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lhbrx => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is2B, '1', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lhz => (LDST, NONE, OP_LOAD, RA_OR_ZERO, CONST_SI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lhzcix => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '1', '0', ZERO, '0', is2B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lhzu => (LDST, NONE, OP_LOAD, RA_OR_ZERO, CONST_SI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_lhzux => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_lhzx => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lwa => (LDST, NONE, OP_LOAD, RA_OR_ZERO, CONST_DS, NONE, RT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '1', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lwarx => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '1', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lwaux => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '1', '1', '0', '0', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_lwax => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '1', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lwbrx => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is4B, '1', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lwz => (LDST, NONE, OP_LOAD, RA_OR_ZERO, CONST_SI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lwzcix => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '1', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_lwzu => (LDST, NONE, OP_LOAD, RA_OR_ZERO, CONST_SI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_lwzux => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', DUPD),
|
|
|
|
INSN_lwzx => (LDST, NONE, OP_LOAD, RA_OR_ZERO, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_maddhd => (ALU, NONE, OP_MUL_H64, RA, RB, RCR, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '1', NONE, '0', '0', NONE),
|
|
|
|
INSN_maddhdu => (ALU, NONE, OP_MUL_H64, RA, RB, RCR, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_maddld => (ALU, NONE, OP_MUL_L64, RA, RB, RCR, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '1', NONE, '0', '0', NONE),
|
|
|
|
INSN_mcrf => (ALU, NONE, OP_CROP, NONE, NONE, NONE, NONE, '1', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_mcrfs => (FPU, FPU, OP_FP_CMP, NONE, NONE, NONE, NONE, '0', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_mcrxrx => (ALU, NONE, OP_MCRXRX, NONE, NONE, NONE, NONE, '0', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_mfcr => (ALU, NONE, OP_MFCR, NONE, NONE, NONE, RT, '1', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_mffs => (FPU, FPU, OP_FP_MISC, NONE, FRB, NONE, FRT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_mfmsr => (ALU, NONE, OP_MFMSR, NONE, NONE, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '1', NONE),
|
|
|
|
INSN_mfspr => (ALU, NONE, OP_MFSPR, NONE, NONE, RS, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_modsd => (DVU, NONE, OP_MOD, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '1', NONE, '0', '0', NONE),
|
|
|
|
INSN_modsw => (DVU, NONE, OP_MOD, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '1', NONE, '0', '0', NONE),
|
|
|
|
INSN_modud => (DVU, NONE, OP_MOD, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_moduw => (DVU, NONE, OP_MOD, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_mtcrf => (ALU, NONE, OP_MTCRF, NONE, NONE, RS, NONE, '0', '1', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_mtfsb => (FPU, FPU, OP_FP_MISC, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_mtfsf => (FPU, FPU, OP_FP_MISC, NONE, FRB, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_mtfsfi => (FPU, FPU, OP_FP_MISC, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_mtmsr => (ALU, NONE, OP_MTMSRD, NONE, NONE, RS, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_mtmsrd => (ALU, NONE, OP_MTMSRD, NONE, NONE, RS, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_mtspr => (ALU, NONE, OP_MTSPR, NONE, NONE, RS, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_mulhd => (ALU, NONE, OP_MUL_H64, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '1', RC, '0', '0', NONE),
|
|
|
|
INSN_mulhdu => (ALU, NONE, OP_MUL_H64, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_mulhw => (ALU, NONE, OP_MUL_H32, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '1', RC, '0', '0', NONE),
|
|
|
|
INSN_mulhwu => (ALU, NONE, OP_MUL_H32, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_mulld => (ALU, NONE, OP_MUL_L64, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '1', RCOE, '0', '0', NONE),
|
|
|
|
INSN_mulli => (ALU, NONE, OP_MUL_L64, RA, CONST_SI, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '1', NONE, '0', '0', NONE),
|
|
|
|
INSN_mullw => (ALU, NONE, OP_MUL_L64, RA, RB, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '1', RCOE, '0', '0', NONE),
|
|
|
|
INSN_nand => (ALU, NONE, OP_LOGIC, NONE, RB, RS, RA, '0', '0', '0', '1', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_neg => (ALU, NONE, OP_ADD, RA, NONE, NONE, RT, '0', '0', '1', '0', ONE, '0', NONE, '0', '0', '0', '0', '0', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_nop => (ALU, NONE, OP_NOP, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_nor => (ALU, NONE, OP_LOGIC, NONE, RB, RS, RA, '0', '0', '1', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '1', RC, '0', '0', NONE),
|
|
|
|
INSN_or => (ALU, NONE, OP_LOGIC, NONE, RB, RS, RA, '0', '0', '1', '1', ZERO, '0', NONE, '0', '0', '0', '0', '0', '1', RC, '0', '0', NONE),
|
|
|
|
INSN_orc => (ALU, NONE, OP_LOGIC, NONE, RB, RS, RA, '0', '0', '0', '1', ZERO, '0', NONE, '0', '0', '0', '0', '0', '1', RC, '0', '0', NONE),
|
|
|
|
INSN_ori => (ALU, NONE, OP_LOGIC, NONE, CONST_UI, RS, RA, '0', '0', '1', '1', ZERO, '0', NONE, '0', '0', '0', '0', '0', '1', NONE, '0', '0', NONE),
|
|
|
|
INSN_oris => (ALU, NONE, OP_LOGIC, NONE, CONST_UI_HI, RS, RA, '0', '0', '1', '1', ZERO, '0', NONE, '0', '0', '0', '0', '0', '1', NONE, '0', '0', NONE),
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
INSN_paddi => (ALU, NONE, OP_ADD, RA0_OR_CIA, CONST_PSI, NONE, RT, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_plbz => (LDST, NONE, OP_LOAD, RA0_OR_CIA, CONST_PSI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_pld => (LDST, NONE, OP_LOAD, RA0_OR_CIA, CONST_PSI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_plfd => (LDST, FPU, OP_LOAD, RA0_OR_CIA, CONST_PSI, NONE, FRT, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_plfs => (LDST, FPU, OP_LOAD, RA0_OR_CIA, CONST_PSI, NONE, FRT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '1', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_plha => (LDST, NONE, OP_LOAD, RA0_OR_CIA, CONST_PSI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is2B, '0', '1', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_plhz => (LDST, NONE, OP_LOAD, RA0_OR_CIA, CONST_PSI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_plwa => (LDST, NONE, OP_LOAD, RA0_OR_CIA, CONST_PSI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '1', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_plwz => (LDST, NONE, OP_LOAD, RA0_OR_CIA, CONST_PSI, NONE, RT, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_pnop => (ALU, NONE, OP_NOP, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_pstb => (LDST, NONE, OP_STORE, RA0_OR_CIA, CONST_PSI, RS, NONE, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_pstd => (LDST, NONE, OP_STORE, RA0_OR_CIA, CONST_PSI, RS, NONE, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_pstfd => (LDST, FPU, OP_STORE, RA0_OR_CIA, CONST_PSI, FRS, NONE, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_pstfs => (LDST, FPU, OP_STORE, RA0_OR_CIA, CONST_PSI, FRS, NONE, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '1', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_psth => (LDST, NONE, OP_STORE, RA0_OR_CIA, CONST_PSI, RS, NONE, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_pstw => (LDST, NONE, OP_STORE, RA0_OR_CIA, CONST_PSI, RS, NONE, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_popcntb => (ALU, NONE, OP_POPCNT, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_popcntd => (ALU, NONE, OP_POPCNT, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_popcntw => (ALU, NONE, OP_POPCNT, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_prtyd => (ALU, NONE, OP_PRTY, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_prtyw => (ALU, NONE, OP_PRTY, NONE, NONE, RS, RA, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_rfid => (ALU, NONE, OP_RFID, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_rldcl => (ALU, NONE, OP_RLCL, NONE, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_rldcr => (ALU, NONE, OP_RLCR, NONE, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_rldic => (ALU, NONE, OP_RLC, NONE, CONST_SH, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_rldicl => (ALU, NONE, OP_RLCL, NONE, CONST_SH, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_rldicr => (ALU, NONE, OP_RLCR, NONE, CONST_SH, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_rldimi => (ALU, NONE, OP_RLC, RA, CONST_SH, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_rlwimi => (ALU, NONE, OP_RLC, RA, CONST_SH32, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_rlwinm => (ALU, NONE, OP_RLC, NONE, CONST_SH32, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_rlwnm => (ALU, NONE, OP_RLC, NONE, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
icache: Restore primary opcode to instruction word
The icache stores a predecoded insn_code value for each instruction,
and so as to fit in 36 bits, omits the primary opcode (the most
significant 6 bits) of each instruction. Previously, for valid
instructions, the primary opcode field of the instruction delivered to
decode1 was a part-representation of the insn_code value rather than
the actual primary opcode. This adds a lookup table to compute the
primary opcode from the insn_code and deliver it in the instruction
words supplied to decode1.
In order that each insn_code can be associated with a single primary
opcode value, the various no-operation instructions with primary
opcode 31 (the reserved no-ops and dss, dst and dstst) have been given
a new insn_code, INSN_rnop, leaving INSN_nop for the preferred no-op
(ori r0,r0,0).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
1 year ago
|
|
|
INSN_rnop => (ALU, NONE, OP_NOP, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_sc => (ALU, NONE, OP_SC, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_setb => (ALU, NONE, OP_SETB, NONE, NONE, NONE, RT, '1', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_slbia => (LDST, NONE, OP_TLBIE, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_sld => (ALU, NONE, OP_SHL, NONE, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_slw => (ALU, NONE, OP_SHL, NONE, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_srad => (ALU, NONE, OP_SHR, NONE, RB, RS, RA, '0', '0', '0', '0', ZERO, '1', NONE, '0', '0', '0', '0', '0', '1', RC, '0', '0', NONE),
|
|
|
|
INSN_sradi => (ALU, NONE, OP_SHR, NONE, CONST_SH, RS, RA, '0', '0', '0', '0', ZERO, '1', NONE, '0', '0', '0', '0', '0', '1', RC, '0', '0', NONE),
|
|
|
|
INSN_sraw => (ALU, NONE, OP_SHR, NONE, RB, RS, RA, '0', '0', '0', '0', ZERO, '1', NONE, '0', '0', '0', '0', '1', '1', RC, '0', '0', NONE),
|
|
|
|
INSN_srawi => (ALU, NONE, OP_SHR, NONE, CONST_SH32, RS, RA, '0', '0', '0', '0', ZERO, '1', NONE, '0', '0', '0', '0', '1', '1', RC, '0', '0', NONE),
|
|
|
|
INSN_srd => (ALU, NONE, OP_SHR, NONE, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_srw => (ALU, NONE, OP_SHR, NONE, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_stb => (LDST, NONE, OP_STORE, RA_OR_ZERO, CONST_SI, RS, NONE, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stbcix => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '1', '0', ZERO, '0', is1B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stbcx => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '0', '1', '0', '0', ONE, '0', '0', NONE),
|
|
|
|
INSN_stbu => (LDST, NONE, OP_STORE, RA_OR_ZERO, CONST_SI, RS, RA, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stbux => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stbx => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '0', '0', ZERO, '0', is1B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_std => (LDST, NONE, OP_STORE, RA_OR_ZERO, CONST_DS, RS, NONE, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stdbrx => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '0', '0', ZERO, '0', is8B, '1', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stdcix => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '1', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stdcx => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '1', '0', '0', ONE, '0', '0', NONE),
|
|
|
|
INSN_stdu => (LDST, NONE, OP_STORE, RA_OR_ZERO, CONST_DS, RS, RA, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stdux => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stdx => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stfd => (LDST, FPU, OP_STORE, RA_OR_ZERO, CONST_SI, FRS, NONE, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stfdu => (LDST, FPU, OP_STORE, RA_OR_ZERO, CONST_SI, FRS, RA, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stfdux => (LDST, FPU, OP_STORE, RA_OR_ZERO, RB, FRS, RA, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stfdx => (LDST, FPU, OP_STORE, RA_OR_ZERO, RB, FRS, NONE, '0', '0', '0', '0', ZERO, '0', is8B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stfiwx => (LDST, FPU, OP_STORE, RA_OR_ZERO, RB, FRS, NONE, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stfs => (LDST, FPU, OP_STORE, RA_OR_ZERO, CONST_SI, FRS, NONE, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '1', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stfsu => (LDST, FPU, OP_STORE, RA_OR_ZERO, CONST_SI, FRS, RA, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '1', '0', '1', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stfsux => (LDST, FPU, OP_STORE, RA_OR_ZERO, RB, FRS, RA, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '1', '0', '1', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stfsx => (LDST, FPU, OP_STORE, RA_OR_ZERO, RB, FRS, NONE, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '1', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_sth => (LDST, NONE, OP_STORE, RA_OR_ZERO, CONST_SI, RS, NONE, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_sthbrx => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '0', '0', ZERO, '0', is2B, '1', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_sthcix => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '1', '0', ZERO, '0', is2B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_sthcx => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '0', '1', '0', '0', ONE, '0', '0', NONE),
|
|
|
|
INSN_sthu => (LDST, NONE, OP_STORE, RA_OR_ZERO, CONST_SI, RS, RA, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_sthux => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_sthx => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '0', '0', ZERO, '0', is2B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stw => (LDST, NONE, OP_STORE, RA_OR_ZERO, CONST_SI, RS, NONE, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stwbrx => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '0', '0', ZERO, '0', is4B, '1', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stwcix => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '1', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stwcx => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '1', '0', '0', ONE, '0', '0', NONE),
|
|
|
|
INSN_stwu => (LDST, NONE, OP_STORE, RA_OR_ZERO, CONST_SI, RS, RA, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stwux => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '1', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_stwx => (LDST, NONE, OP_STORE, RA_OR_ZERO, RB, RS, NONE, '0', '0', '0', '0', ZERO, '0', is4B, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_subf => (ALU, NONE, OP_ADD, RA, RB, NONE, RT, '0', '0', '1', '0', ONE, '0', NONE, '0', '0', '0', '0', '0', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_subfc => (ALU, NONE, OP_ADD, RA, RB, NONE, RT, '0', '0', '1', '0', ONE, '1', NONE, '0', '0', '0', '0', '0', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_subfe => (ALU, NONE, OP_ADD, RA, RB, NONE, RT, '0', '0', '1', '0', CA, '1', NONE, '0', '0', '0', '0', '0', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_subfic => (ALU, NONE, OP_ADD, RA, CONST_SI, NONE, RT, '0', '0', '1', '0', ONE, '1', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_subfme => (ALU, NONE, OP_ADD, RA, CONST_M1, NONE, RT, '0', '0', '1', '0', CA, '1', NONE, '0', '0', '0', '0', '0', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_subfze => (ALU, NONE, OP_ADD, RA, NONE, NONE, RT, '0', '0', '1', '0', CA, '1', NONE, '0', '0', '0', '0', '0', '0', RCOE, '0', '0', NONE),
|
|
|
|
INSN_sync => (ALU, NONE, OP_NOP, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_td => (ALU, NONE, OP_TRAP, RA, RB, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_tdi => (ALU, NONE, OP_TRAP, RA, CONST_SI, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_tlbie => (LDST, NONE, OP_TLBIE, NONE, RB, RS, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_tlbiel => (LDST, NONE, OP_TLBIE, NONE, RB, RS, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_tlbsync => (ALU, NONE, OP_NOP, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_tw => (ALU, NONE, OP_TRAP, RA, RB, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_twi => (ALU, NONE, OP_TRAP, RA, CONST_SI, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '1', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_wait => (ALU, NONE, OP_NOP, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_xor => (ALU, NONE, OP_XOR, NONE, RB, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', RC, '0', '0', NONE),
|
|
|
|
INSN_xori => (ALU, NONE, OP_XOR, NONE, CONST_UI, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
INSN_xoris => (ALU, NONE, OP_XOR, NONE, CONST_UI_HI, RS, RA, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE),
|
|
|
|
|
|
|
|
others => (ALU, NONE, OP_ILLEGAL, NONE, NONE, NONE, NONE, '0', '0', '0', '0', ZERO, '0', NONE, '0', '0', '0', '0', '0', '0', NONE, '0', '0', NONE)
|
|
|
|
);
|
|
|
|
|
|
|
|
function decode_ram_spr(sprn : spr_num_t) return ram_spr_info is
|
|
|
|
variable ret : ram_spr_info;
|
|
|
|
begin
|
|
|
|
ret := (index => (others => '0'), isodd => '0', valid => '1');
|
|
|
|
case sprn is
|
|
|
|
when SPR_LR =>
|
|
|
|
ret.index := RAMSPR_LR;
|
|
|
|
when SPR_CTR =>
|
|
|
|
ret.index := RAMSPR_CTR;
|
|
|
|
ret.isodd := '1';
|
|
|
|
when SPR_TAR =>
|
|
|
|
ret.index := RAMSPR_TAR;
|
|
|
|
when SPR_SRR0 =>
|
|
|
|
ret.index := RAMSPR_SRR0;
|
|
|
|
when SPR_SRR1 =>
|
|
|
|
ret.index := RAMSPR_SRR1;
|
|
|
|
ret.isodd := '1';
|
|
|
|
when SPR_HSRR0 =>
|
|
|
|
ret.index := RAMSPR_HSRR0;
|
|
|
|
when SPR_HSRR1 =>
|
|
|
|
ret.index := RAMSPR_HSRR1;
|
|
|
|
ret.isodd := '1';
|
|
|
|
when SPR_SPRG0 =>
|
|
|
|
ret.index := RAMSPR_SPRG0;
|
|
|
|
when SPR_SPRG1 =>
|
|
|
|
ret.index := RAMSPR_SPRG1;
|
|
|
|
ret.isodd := '1';
|
|
|
|
when SPR_SPRG2 =>
|
|
|
|
ret.index := RAMSPR_SPRG2;
|
|
|
|
when SPR_SPRG3 | SPR_SPRG3U =>
|
|
|
|
ret.index := RAMSPR_SPRG3;
|
|
|
|
ret.isodd := '1';
|
|
|
|
when SPR_HSPRG0 =>
|
|
|
|
ret.index := RAMSPR_HSPRG0;
|
|
|
|
when SPR_HSPRG1 =>
|
|
|
|
ret.index := RAMSPR_HSPRG1;
|
|
|
|
ret.isodd := '1';
|
|
|
|
when others =>
|
|
|
|
ret.valid := '0';
|
|
|
|
end case;
|
|
|
|
return ret;
|
|
|
|
end;
|
|
|
|
|
|
|
|
function map_spr(sprn : spr_num_t) return spr_id is
|
|
|
|
variable i : spr_id;
|
|
|
|
begin
|
|
|
|
i.sel := "000";
|
|
|
|
i.valid := '1';
|
|
|
|
i.ispmu := '0';
|
|
|
|
case sprn is
|
|
|
|
when SPR_TB =>
|
|
|
|
i.sel := SPRSEL_TB;
|
|
|
|
when SPR_TBU =>
|
|
|
|
i.sel := SPRSEL_TBU;
|
|
|
|
when SPR_DEC =>
|
|
|
|
i.sel := SPRSEL_DEC;
|
|
|
|
when SPR_PVR =>
|
|
|
|
i.sel := SPRSEL_PVR;
|
|
|
|
when 724 => -- LOG_ADDR SPR
|
|
|
|
i.sel := SPRSEL_LOGA;
|
|
|
|
when 725 => -- LOG_DATA SPR
|
|
|
|
i.sel := SPRSEL_LOGD;
|
|
|
|
when SPR_UPMC1 | SPR_UPMC2 | SPR_UPMC3 | SPR_UPMC4 | SPR_UPMC5 | SPR_UPMC6 |
|
|
|
|
SPR_UMMCR0 | SPR_UMMCR1 | SPR_UMMCR2 | SPR_UMMCRA | SPR_USIER | SPR_USIAR | SPR_USDAR |
|
|
|
|
SPR_PMC1 | SPR_PMC2 | SPR_PMC3 | SPR_PMC4 | SPR_PMC5 | SPR_PMC6 |
|
|
|
|
SPR_MMCR0 | SPR_MMCR1 | SPR_MMCR2 | SPR_MMCRA | SPR_SIER | SPR_SIAR | SPR_SDAR =>
|
|
|
|
i.ispmu := '1';
|
|
|
|
when SPR_CFAR =>
|
|
|
|
i.sel := SPRSEL_CFAR;
|
|
|
|
when SPR_XER =>
|
|
|
|
i.sel := SPRSEL_XER;
|
|
|
|
when others =>
|
|
|
|
i.valid := '0';
|
|
|
|
end case;
|
|
|
|
return i;
|
|
|
|
end;
|
|
|
|
|
|
|
|
begin
|
|
|
|
decode1_0: process(clk)
|
|
|
|
begin
|
|
|
|
if rising_edge(clk) then
|
|
|
|
if rst = '1' then
|
|
|
|
r <= Decode1ToDecode2Init;
|
|
|
|
fetch_failed <= '0';
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
pr <= prefix_state_init;
|
|
|
|
elsif flush_in = '1' then
|
|
|
|
r.valid <= '0';
|
|
|
|
fetch_failed <= '0';
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
pr <= prefix_state_init;
|
|
|
|
elsif stall_in = '0' then
|
|
|
|
r <= rin;
|
|
|
|
fetch_failed <= f_in.fetch_failed;
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
if f_in.valid = '1' then
|
|
|
|
pr <= pr_in;
|
|
|
|
end if;
|
|
|
|
end if;
|
|
|
|
if rst = '1' then
|
|
|
|
br.predict <= '0';
|
|
|
|
else
|
|
|
|
br <= br_in;
|
|
|
|
end if;
|
|
|
|
end if;
|
|
|
|
end process;
|
|
|
|
|
|
|
|
busy_out <= stall_in;
|
|
|
|
|
|
|
|
decode1_rom: process(clk)
|
|
|
|
begin
|
|
|
|
if rising_edge(clk) then
|
|
|
|
if stall_in = '0' then
|
|
|
|
decode <= decode_rom(decode_rom_addr);
|
|
|
|
end if;
|
|
|
|
end if;
|
|
|
|
end process;
|
|
|
|
|
|
|
|
decode1_1: process(all)
|
|
|
|
variable v : Decode1ToDecode2Type;
|
|
|
|
variable vr : Decode1ToRegisterFileType;
|
|
|
|
variable br_nia : std_ulogic_vector(61 downto 0);
|
|
|
|
variable br_offset : std_ulogic_vector(23 downto 0);
|
|
|
|
variable bv : br_predictor_t;
|
|
|
|
variable icode : insn_code;
|
|
|
|
variable sprn : spr_num_t;
|
|
|
|
variable maybe_rb : std_ulogic;
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
variable pv : prefix_state_t;
|
|
|
|
variable icode_bits : std_ulogic_vector(9 downto 0);
|
|
|
|
variable valid_suffix : std_ulogic;
|
|
|
|
begin
|
|
|
|
v := Decode1ToDecode2Init;
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
pv := pr;
|
|
|
|
|
|
|
|
v.valid := f_in.valid;
|
|
|
|
v.nia := f_in.nia;
|
|
|
|
v.insn := f_in.insn;
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
v.prefix := pr.prefix;
|
|
|
|
v.prefixed := pr.prefixed;
|
|
|
|
v.stop_mark := f_in.stop_mark;
|
|
|
|
v.big_endian := f_in.big_endian;
|
|
|
|
|
|
|
|
if is_X(f_in.insn) then
|
|
|
|
v.spr_info := (sel => "XXX", others => 'X');
|
|
|
|
v.ram_spr := (index => (others => 'X'), others => 'X');
|
|
|
|
else
|
|
|
|
sprn := decode_spr_num(f_in.insn);
|
|
|
|
v.spr_info := map_spr(sprn);
|
|
|
|
v.ram_spr := decode_ram_spr(sprn);
|
|
|
|
end if;
|
|
|
|
|
|
|
|
icode := f_in.icode;
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
icode_bits := std_ulogic_vector(to_unsigned(insn_code'pos(icode), 10));
|
|
|
|
|
|
|
|
if f_in.fetch_failed = '1' then
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
icode_bits := std_ulogic_vector(to_unsigned(insn_code'pos(INSN_fetch_fail), 10));
|
|
|
|
-- Only send down a single OP_FETCH_FAILED
|
|
|
|
v.valid := not fetch_failed;
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
pv := prefix_state_init;
|
|
|
|
|
|
|
|
elsif pr.prefixed = '1' then
|
|
|
|
-- Check suffix value and convert to the prefixed instruction code
|
|
|
|
if pr.prefix(24) = '1' then
|
|
|
|
-- either pnop or illegal
|
|
|
|
icode_bits := std_ulogic_vector(to_unsigned(insn_code'pos(INSN_pnop), 10));
|
|
|
|
else
|
|
|
|
-- various load/store instructions
|
|
|
|
icode_bits(0) := '1';
|
|
|
|
end if;
|
|
|
|
valid_suffix := '0';
|
|
|
|
case pr.prefix(25 downto 23) is
|
|
|
|
when "000" => -- 8LS
|
|
|
|
if icode >= INSN_first_8ls and icode < INSN_first_rb then
|
|
|
|
valid_suffix := '1';
|
|
|
|
end if;
|
|
|
|
when "100" => -- MLS
|
|
|
|
if icode >= INSN_first_mls and icode < INSN_first_8ls then
|
|
|
|
valid_suffix := '1';
|
|
|
|
elsif icode >= INSN_first_fp_mls and icode < INSN_first_fp_nonmls then
|
|
|
|
valid_suffix := '1';
|
|
|
|
end if;
|
|
|
|
when "110" => -- MRR, i.e. pnop
|
|
|
|
if pr.prefix(22 downto 20) = "000" then
|
|
|
|
valid_suffix := '1';
|
|
|
|
end if;
|
|
|
|
when others =>
|
|
|
|
end case;
|
|
|
|
v.nia(5 downto 2) := pr.pref_ia;
|
|
|
|
v.prefixed := '1';
|
|
|
|
v.prefix := pr.prefix;
|
|
|
|
v.illegal_suffix := not valid_suffix;
|
|
|
|
pv := prefix_state_init;
|
|
|
|
|
|
|
|
elsif icode = INSN_prefix then
|
|
|
|
pv.prefixed := '1';
|
|
|
|
pv.pref_ia := f_in.nia(5 downto 2);
|
|
|
|
pv.prefix := f_in.insn(25 downto 0);
|
Implement interrupts for prefixed instructions
This arranges to generate an illegal instruction type program
interrupt for illegal prefixed instructions, that is, those where the
suffix is not a legal value given the prefix, or the prefix has a
reserved value in the subtype field. This implementation doesn't
generate an interrupt for the invalid 8LS:D and MLS:D instruction
forms where R = 1 and RA != 0. (In those cases it uses (RA) as the
addend, i.e. it ignores the R bit.)
This detects the case where the address of an instruction prefix is
equal mod 64 to 60, and generates an alignment interrupt in that case.
This also arranges to set bit 34 of SRR1 when an interrupt occurs due
to a prefixed instruction, for those interrupts where that is required
(i.e. trace, alignment, floating-point unavailable, data storage, data
segment, and most cases of program interrupt).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
-- Check if the address of the prefix mod 64 is 60;
|
|
|
|
-- if so we need to arrange to generate an alignment interrupt
|
|
|
|
if f_in.nia(5 downto 2) = "1111" then
|
|
|
|
v.misaligned_prefix := '1';
|
|
|
|
else
|
|
|
|
v.valid := '0';
|
|
|
|
end if;
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
|
|
|
|
end if;
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
decode_rom_addr <= insn_code'val(to_integer(unsigned(icode_bits)));
|
|
|
|
|
|
|
|
if f_in.valid = '1' then
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
report "Decode " & insn_code'image(insn_code'val(to_integer(unsigned(icode_bits)))) & " " &
|
|
|
|
to_hstring(f_in.insn) & " at " & to_hstring(f_in.nia);
|
|
|
|
end if;
|
|
|
|
|
|
|
|
-- Branch predictor
|
|
|
|
-- Note bclr, bcctr and bctar not predicted as we have no
|
|
|
|
-- count cache or link stack.
|
|
|
|
br_offset := f_in.insn(25 downto 2);
|
|
|
|
case icode is
|
|
|
|
when INSN_brel | INSN_babs =>
|
|
|
|
-- Unconditional branches are always taken
|
|
|
|
v.br_pred := '1';
|
|
|
|
when INSN_bcrel =>
|
|
|
|
-- Predict backward relative branches as taken, others as untaken
|
|
|
|
v.br_pred := f_in.insn(15);
|
|
|
|
br_offset(23 downto 14) := (others => '1');
|
|
|
|
when others =>
|
|
|
|
end case;
|
|
|
|
br_nia := f_in.nia(63 downto 2);
|
|
|
|
if f_in.insn(1) = '1' then
|
|
|
|
br_nia := (others => '0');
|
|
|
|
end if;
|
|
|
|
bv.br_target := signed(br_nia) + signed(br_offset);
|
fetch1: Implement a simple branch target cache
This implements a cache in fetch1, where each entry stores the address
of a simple branch instruction (b or bc) and the target of the branch.
When fetching sequentially, if the address being fetched matches the
cache entry, then fetching will be redirected to the branch target.
The cache has 1024 entries and is direct-mapped, i.e. indexed by bits
11..2 of the NIA.
The bus from execute1 now carries information about taken and
not-taken simple branches, which fetch1 uses to update the cache.
The cache entry is updated for both taken and not-taken branches, with
the valid bit being set if the branch was taken and cleared if the
branch was not taken.
If fetching is redirected to the branch target then that goes down the
pipe as a predicted-taken branch, and decode1 does not do any static
branch prediction. If fetching is not redirected, then the next
instruction goes down the pipe as normal and decode1 does its static
branch prediction.
In order to make timing, the lookup of the cache is pipelined, so on
each cycle the cache entry for the current NIA + 8 is read. This
means that after a redirect (from decode1 or execute1), only the third
and subsequent sequentially-fetched instructions will be able to be
predicted.
This improves the coremark value on the Arty A7-100 from about 180 to
about 190 (more than 5%).
The BTC is optional. Builds for the Artix 7 35-T part have it off by
default because the extra ~1420 LUTs it takes mean that the design
doesn't fit on the Arty A7-35 board.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
|
|
|
if f_in.next_predicted = '1' then
|
|
|
|
v.br_pred := '1';
|
|
|
|
elsif f_in.next_pred_ntaken = '1' then
|
|
|
|
v.br_pred := '0';
|
fetch1: Implement a simple branch target cache
This implements a cache in fetch1, where each entry stores the address
of a simple branch instruction (b or bc) and the target of the branch.
When fetching sequentially, if the address being fetched matches the
cache entry, then fetching will be redirected to the branch target.
The cache has 1024 entries and is direct-mapped, i.e. indexed by bits
11..2 of the NIA.
The bus from execute1 now carries information about taken and
not-taken simple branches, which fetch1 uses to update the cache.
The cache entry is updated for both taken and not-taken branches, with
the valid bit being set if the branch was taken and cleared if the
branch was not taken.
If fetching is redirected to the branch target then that goes down the
pipe as a predicted-taken branch, and decode1 does not do any static
branch prediction. If fetching is not redirected, then the next
instruction goes down the pipe as normal and decode1 does its static
branch prediction.
In order to make timing, the lookup of the cache is pipelined, so on
each cycle the cache entry for the current NIA + 8 is read. This
means that after a redirect (from decode1 or execute1), only the third
and subsequent sequentially-fetched instructions will be able to be
predicted.
This improves the coremark value on the Arty A7-100 from about 180 to
about 190 (more than 5%).
The BTC is optional. Builds for the Artix 7 35-T part have it off by
default because the extra ~1420 LUTs it takes mean that the design
doesn't fit on the Arty A7-35 board.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
4 years ago
|
|
|
end if;
|
|
|
|
bv.predict := v.br_pred and f_in.valid and not flush_in and not busy_out and not f_in.next_predicted;
|
|
|
|
|
|
|
|
-- Work out GPR/FPR read addresses
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
-- Note that for prefixed instructions we are working this out based
|
|
|
|
-- only on the suffix.
|
|
|
|
maybe_rb := '0';
|
|
|
|
vr.reg_1_addr := '0' & insn_ra(f_in.insn);
|
|
|
|
vr.reg_2_addr := '0' & insn_rb(f_in.insn);
|
|
|
|
vr.reg_3_addr := '0' & insn_rs(f_in.insn);
|
|
|
|
if icode >= INSN_first_rb then
|
|
|
|
maybe_rb := '1';
|
|
|
|
if icode < INSN_first_frs then
|
|
|
|
if icode >= INSN_first_rc then
|
|
|
|
vr.reg_3_addr := '0' & insn_rcreg(f_in.insn);
|
|
|
|
end if;
|
|
|
|
else
|
|
|
|
-- access FRS operand
|
|
|
|
vr.reg_3_addr(5) := '1';
|
|
|
|
if icode >= INSN_first_frab then
|
|
|
|
-- access FRA and/or FRB operands
|
|
|
|
vr.reg_1_addr(5) := '1';
|
|
|
|
vr.reg_2_addr(5) := '1';
|
|
|
|
end if;
|
|
|
|
if icode >= INSN_first_frabc then
|
|
|
|
-- access FRC operand
|
|
|
|
vr.reg_3_addr := '1' & insn_rcreg(f_in.insn);
|
|
|
|
end if;
|
|
|
|
end if;
|
|
|
|
end if;
|
|
|
|
vr.read_1_enable := f_in.valid;
|
|
|
|
vr.read_2_enable := f_in.valid and maybe_rb;
|
|
|
|
vr.read_3_enable := f_in.valid;
|
|
|
|
|
|
|
|
v.reg_a := vr.reg_1_addr;
|
|
|
|
v.reg_b := vr.reg_2_addr;
|
|
|
|
v.reg_c := vr.reg_3_addr;
|
|
|
|
|
|
|
|
-- Update registers
|
|
|
|
rin <= v;
|
|
|
|
br_in <= bv;
|
Decode prefixed instructions
This adds logic to do basic decoding of the prefixed instructions
defined in PowerISA v3.1B which are in the SFFS (Scalar Fixed plus
Floating-Point Subset) compliancy subset. In PowerISA v3.1B SFFS,
there are 14 prefixed load/store instructions plus the prefixed no-op
instruction (pnop). The prefixed load/store instructions all use an
extended version of D-form, which has an extra 18 bits of displacement
in the prefix, plus an 'R' bit which enables PC-relative addressing.
When decode1 sees an instruction word where the insn_code is
INSN_prefix (i.e. the primary opcode was 1), it stores the prefix word
and sends nothing down to decode2 in that cycle. When the next valid
instruction word arrives, it is interpreted as a suffix, meaning that
its insn_code gets modified before being used to look up the decode
table.
The insn_code values are rearranged so that the values for
instructions which are the suffix of a valid prefixed instruction are
all at even indexes, and the corresponding prefixed instructions
follow immediately, so that an insn_code value can be converted to the
corresponding prefixed value by setting the LSB of the insn_code
value. There are two prefixed instructions, pld and pstd, for which
the suffix is not a valid SFFS instruction by itself, so these have
been given dummy insn_code values which decode as illegal (INSN_op57
and INSN_op61).
For a prefixed instruction, decode1 examines the type and subtype
fields of the prefix and checks that the suffix is valid for the type
and subtype. This check doesn't affect which entry of the decode
table is used; the result is passed down to decode2, and will in
future be acted upon in execute1.
The instruction address passed down to decode2 is the address of the
prefix. To enable this, part of the instruction address is saved when
the prefix is seen, and then the instruction address received from
icache is partly overlaid by the saved prefix address. Because
prefixed instructions are not permitted to cross 64-byte boundaries,
we only need to save bits 5:2 of the instruction to do this. If the
alignment restriction ever gets relaxed, we will then need to save
more bits of the address.
Decode2 has been extended to handle the R bit of the prefix (in 8LS
and MLS forms) and to be able to generate the 34-bit immediate value
from the prefix and suffix.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
pr_in <= pv;
|
|
|
|
|
|
|
|
-- Update outputs
|
|
|
|
d_out <= r;
|
|
|
|
d_out.decode <= decode;
|
|
|
|
r_out <= vr;
|
|
|
|
f_out.redirect <= br.predict;
|
|
|
|
f_out.redirect_nia <= std_ulogic_vector(br.br_target) & "00";
|
|
|
|
flush_out <= bv.predict or br.predict;
|
|
|
|
end process;
|
|
|
|
|
|
|
|
d1_log: if LOG_LENGTH > 0 generate
|
|
|
|
signal log_data : std_ulogic_vector(12 downto 0);
|
|
|
|
begin
|
|
|
|
dec1_log : process(clk)
|
|
|
|
begin
|
|
|
|
if rising_edge(clk) then
|
decode1: Use block RAMs in decode
This combines the various decode arrays in decode1 into two, one
indexed by the major opcode (bits 31--26 of the instruction) together
with bits 4--0 of the instruction, and the other indexed mostly by the
minor opcode (bits 10--1), with some swizzles to accommodate the
relevant parts of the minor opcode space for opcodes 19, 31, 59 and 63
within a 2k entry ROM (11 address bits). These are called the "major"
and the "row" decode ROMs respectively. (Bits 10--6 of the
instruction are called the "row index", and bits 5--1, or 5--0 for
some opcodes, are called the "column index", because of the way the
opcode maps in the ISA are laid out.)
Both ROMs are looked up each cycle and the result from one or other,
or from an override in ri.override_decode, are selected after a clock
edge.
This uses quite a lot of BRAM resources. In future a predecode step
will reduce the BRAM usage substantially.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
log_data <= std_ulogic_vector(to_unsigned(insn_type_t'pos(d_out.decode.insn_type), 6)) &
|
|
|
|
r.nia(5 downto 2) &
|
decode1: Use block RAMs in decode
This combines the various decode arrays in decode1 into two, one
indexed by the major opcode (bits 31--26 of the instruction) together
with bits 4--0 of the instruction, and the other indexed mostly by the
minor opcode (bits 10--1), with some swizzles to accommodate the
relevant parts of the minor opcode space for opcodes 19, 31, 59 and 63
within a 2k entry ROM (11 address bits). These are called the "major"
and the "row" decode ROMs respectively. (Bits 10--6 of the
instruction are called the "row index", and bits 5--1, or 5--0 for
some opcodes, are called the "column index", because of the way the
opcode maps in the ISA are laid out.)
Both ROMs are looked up each cycle and the result from one or other,
or from an override in ri.override_decode, are selected after a clock
edge.
This uses quite a lot of BRAM resources. In future a predecode step
will reduce the BRAM usage substantially.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2 years ago
|
|
|
std_ulogic_vector(to_unsigned(unit_t'pos(d_out.decode.unit), 2)) &
|
|
|
|
r.valid;
|
|
|
|
end if;
|
|
|
|
end process;
|
|
|
|
log_out <= log_data;
|
|
|
|
end generate;
|
|
|
|
|
|
|
|
end architecture behaviour;
|