This just returns the value from the inverse lookup table. The result
is accurate to better than one part in 512 (the architecture requires
1/256).
This also adds a simple test, which relies on the particular values in
the inverse lookup table, so it is not a general test.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This implements floating-point division A/B by a process that starts
with normalizing both inputs if necessary. Then an estimate of 1/B
from a lookup table is refined by 3 Newton-Raphson iterations and then
multiplied by A to get a quotient. The remainder is calculated as
A - R * B (where R is the result, i.e. the quotient) and the remainder
is compared to 0 and to B to see whether the quotient needs to be
incremented by 1. The calculations of 1 / B are done with 56 fraction
bits and intermediate results are truncated rather than rounded,
meaning that the final estimate of 1 / B is always correct or a little
bit low, never too high, and thus the calculated quotient is correct
or 1 unit too low. Doing the estimate of 1 / B with sufficient
precision that the quotient is always correct to the last bit without
needing any adjustment would require many more bits of precision.
This implements fdivs by computing a double-precision quotient and
then rounding it to single precision. It would be possible to
optimize this by e.g. doing only 2 iterations of Newton-Raphson and
then doing the remainder calculation and adjustment at single
precision rather than double precision.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This implements the fmul and fmuls instructions.
For fmul[s] with denormalized operands we normalize the inputs
before doing the multiplication, to eliminate the need for doing
count-leading-zeroes on P. This adds 3 or 5 cycles to the
execution time when one or both operands are denormalized.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This implements fctiw, fctiwz, fctiwu, fctiwuz, fctid, fctidz, fctidu
and fctiduz, and adds tests for them.
There are some subtleties around the setting of the inexact (XX) and
invalid conversion (VXCVI) flags in the FPSCR. If the rounded value
ends up being out of range, we need to set VXCVI and not XX. For a
conversion to unsigned word or doubleword of a negative value that
rounds to zero, we need to set XX and not VXCVI.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This brings in the invalid exception for the case of frsp with a
signalling NaN as input, and the need to be able to convert a
signalling NaN to a quiet NaN.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This implements fcfid, fcfidu, fcfids and fcfidus, which convert
64-bit integer values in an FPR into a floating-point value.
This brings in a lot of the datapath that will be needed in
future, including the shifter, adder, mask generator and
count-leading-zeroes logic, along with the machinery for rounding
to single-precision or double-precision, detecting inexact results,
signalling inexact-result exceptions, and updating result flags
in the FPSCR.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This implements fmr, fneg, fabs, fnabs and fcpsgn and adds tests
for them.
This adds logic to unpack and repack floating-point data from the
64-bit packed form (as stored in memory and the register file) into
the unpacked form in the fpr_reg_type record. This is not strictly
necessary for fmr et al., but will be useful for when we do actual
arithmetic.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds the skeleton of a floating-point unit and implements the
mffs and mtfsf instructions.
Execute1 sends FP instructions to the FPU and receives busy,
exception, FP interrupt and illegal interrupt signals from it.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to loadstore1 to convert between single-precision and
double-precision formats, and implements the lfs* and stfs*
instructions. The conversion processes are described in Power ISA
v3.1 Book 1 sections 4.6.2 and 4.6.3.
These conversions take one cycle, so lfs* and stfs* are one cycle
slower than lfd* and stfd*.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This extends the register file so it can hold FPR values, and
implements the FP loads and stores that do not require conversion
between single and double precision.
We now have the FP, FE0 and FE1 bits in MSR. FP loads and stores
cause a FP unavailable interrupt if MSR[FP] = 0.
The FPU facilities are optional and their presence is controlled by
the HAS_FPU generic passed down from the top-level board file. It
defaults to true for all except the A7-35 boards.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Trace interrupts occur when the MSR[TE] field is non-zero and an
instruction other than rfid has been successfully completed. A trace
interrupt occurs before the next instruction is executed or any
asynchronous interrupt is taken.
Since the trace interrupt is defined to set SRR1 bits depending on
whether the traced instruction is a load or an instruction treated as
a load, or a store or an instruction treated as a store, we need to
make sure the treated-as-a-load instructions (icbi, icbt, dcbt, dcbst,
dcbf) and the treated-as-a-store instructions (dcbtst, dcbz) have the
correct opcodes in decode1. Several of them were previously marked as
OP_NOP.
We don't yet implement the SIAR or SDAR registers, which should be set
by trace interrupts.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
In the cases where we need to override the values from the decode ROMs,
we now do that overriding after the clock edge (eating into decode2's
cycle) rather than before. This helps timing a little.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
To avoid adding too much logic, this moves the adder used by OP_ADD
out of the case statement in execute1.vhdl so that the result can
be used by OP_ADDG6S as well.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
These are no-ops that are reserved for future use as performance
hints, so we just need to treat them as no-ops.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The addex instruction is like adde but uses the XER[OV] bit for the
carry in and out rather than XER[CA].
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a true random number generator for the Xilinx FPGAs which
uses a set of chaotic ring oscillators to generate random bits and
then passes them through a Linear Hybrid Cellular Automaton (LHCA) to
remove bias, as described in "High Speed True Random Number Generators
in Xilinx FPGAs" by Catalin Baetoniu of Xilinx Inc., in:
https://pdfs.semanticscholar.org/83ac/9e9c1bb3dad5180654984604c8d5d8137412.pdf
This requires adding a .xdc file to tell vivado that the combinatorial
loops that form the ring oscillators are intentional. The same
code should work on other FPGAs as well if their tools can be told to
accept the combinatorial loops.
For simulation, the random.vhdl module gets compiled in, which uses
the pseudorand() function to generate random numbers.
Synthesis using yosys uses nonrandom.vhdl, which always signals an
error, causing darn to return 0xffff_ffff_ffff_ffff.
This adds an implementation of the darn instruction. Darn can return
either raw or conditioned random numbers. On Xilinx FPGAs, reading a
raw random number gives the output of the ring oscillators, and
reading a conditioned random number gives the output of the LHCA.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
These instructions use major opcode 4 and have a third GPR input
operand, so we need a decode table for major opcode 4 and some
plumbing to get the RC register operand read.
The multiply-add instructions use the same insn_type_t values as the
regular multiply instructions, and we distinguish in execute1 by
looking at the major opcode. This turns out to be convenient because
we don't have to add any cases in the code that handles the output of
the multiplier, and it frees up some insn_type_t values.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This also removes OP_MCRXR, as the mcrxr instruction was removed in
version 3.0B of the Power ISA, having been phased-out for the server
architecture since v2.02.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Commit d5c8c33bae ("decode1: Reformat to 4-space indentation") resulted
in some rows of major_decode_rom_array being misaligned. This fixes it.
No code change.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds "if LOG_LENGTH > 0 generate" to the places in the core
where log output data is latched, so that when LOG_LENGTH = 0 we
don't create the logic to collect the data which won't be stored.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a path to allow the CR result of one instruction to be
forwarded to the next instruction, so that sequences such as
cmp; bc can avoid having a 1-cycle bubble.
Forwarding is not available for dot-form (Rc=1) instructions,
since the CR result for them is calculated in writeback. The
decode.output_cr field is used to identify those instructions
that compute the CR result in execute1.
For some reason, the multiply instructions incorrectly had
output_cr = 1 in the decode tables. This fixes that.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This implements the CFAR SPR as a slow SPR stored in 'ctrl'. Taken
branches and rfid update it to the address of the branch or rfid
instruction.
To simplify the logic, this makes rfid use the branch logic to
generate its redirect (requiring SRR0 to come in to execute1 on
the B input and SRR1 on the A input), and the masking of the bottom
2 bits of NIA is moved to fetch1.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This implements a simple branch predictor in the decode1 stage. If it
sees that the instruction is b or bc and the branch is predicted to be
taken, it sends a flush and redirect upstream (to icache and fetch1)
to redirect fetching to the branch target. The prediction is sent
downstream with the branch instruction, and execute1 now only sends
a flush/redirect upstream if the prediction was wrong. Unconditional
branches are always predicted to be taken, and conditional branches
are predicted to be taken if and only if the offset is negative.
Branches that take the branch address from a register (bclr, bcctr)
are predicted not taken, as we don't have any way to predict the
branch address.
Since we can now have a mflr being executed immediately after a bl
or bcl, we now track the update to LR in the hazard tracker, using
the second write register field that is used to track RA updates for
update-form loads and stores.
For those branches that update LR but don't write any other result
(i.e. that don't decrementer CTR), we now write back LR in the same
cycle as the instruction rather than taking a second cycle for the
LR writeback.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This makes the logic that works out decode.unit and decode.sgl_pipe
for mtspr/mfspr to/from slow SPRs detect the fact that the
instruction is mtspr/mfspr based on a match with the instruction
word rather than looking at v.decode.insn_type. This improves timing
substantially, as the ROM lookup to get v.decode is relatively slow.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This means that the busy signal from execute1 (which can be driven
combinatorially from mmu or dcache) now stops at decode1 and doesn't
go on to icache or fetch1. This helps with timing.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This makes the logic that calculates which SPRs are being accessed
work in parallel with the instruction decode ROM lookup instead of
being dependent on the opcode found in the decode ROM. The reason
for doing that is that the path from icache through the decode ROM
to the ispr1/ispr2 fields has become a critical path.
Thus we are now using only a very partial decode of the instruction
word in the logic for isp1/isp2, and we therefore can no longer rely
on them being zero in all cases where no SPR is being accessed.
Instead, decode2 now ignores ispr1/ispr2 in all cases except when the
relevant decode.input_reg_a/b or decode.output_reg_a is set to SPR.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The fetch2 stage existed primarily to provide a stash buffer for the
output of icache when a stall occurred. However, we can get the same
effect -- of having the input to decode1 stay unchanged on a stall
cycle -- by using the read enable of the BRAMs in icache, and by
adding logic to keep the outputs unchanged on a clock cycle when
stall_in = 1. This reduces branch and interrupt latency by one
cycle.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This logs 256 bits of data per cycle to a ring buffer in BRAM. The
data collected can be read out through 2 new SPRs or through the
debug interface.
The new SPRs are LOG_ADDR (724) and LOG_DATA (725). LOG_ADDR contains
the buffer write pointer in the upper 32 bits (in units of entries,
i.e. 32 bytes) and the read pointer in the lower 32 bits (in units of
doublewords, i.e. 8 bytes). Reading LOG_DATA gives the doubleword
from the buffer at the read pointer and increments the read pointer.
Setting bit 31 of LOG_ADDR inhibits the trace log system from writing
to the log buffer, so the contents are stable and can be read.
There are two new debug addresses which function similarly to the
LOG_ADDR and LOG_DATA SPRs. The log is frozen while either or both of
the LOG_ADDR SPR bit 31 or the debug LOG_ADDR register bit 31 are set.
The buffer defaults to 2048 entries, i.e. 64kB. The size is set by
the LOG_LENGTH generic on the core_debug module. Software can
determine the length of the buffer because the length is ORed into the
buffer write pointer in the upper 32 bits of LOG_ADDR. Hence the
length of the buffer can be calculated as 1 << (31 - clz(LOG_ADDR)).
There is a program to format the log entries in a somewhat readable
fashion in scripts/fmt_log/fmt_log.c. The log_entry struct in that
file describes the layout of the bits in the log entries.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
These were missed earlier when the single-issue flag was turned off on
the other loads and stores by commit 1a244d3470 ("Remove single-issue
constraint for most loads and stores").
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
By adding logic to decode2 to be able to send the instruction address
down the A input, and making CONST_DX_HI (renamed to CONST_DXHI4) add
4 to the immediate value (easy since the bottom 16 bits were zero),
we can do addpcis using the main adder. This reduces the width of the
result mux and frees up one value in insn_type_t, since we can now use
OP_ADD for addpcis.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This commit adds support for the addpcis instruction from ISA 3.0.
A new input_reg_b_t type, CONST_DX_HI, was added to support the
shifted immediate value used in DX-Form instructions.
Signed-off-by: Shawn Anastasio <shawn@anastas.io>
This adds the PID register and repurposes SPR 720 as the PRTBL
register, which points to the base of the process table. There
doesn't seem to be any point to implementing the partition table given
that we don't have hypervisor mode.
The MMU caches entry 0 of the process table internally (in pgtbl3)
plus the entry indexed by the value in the PID register (pgtbl0).
Both caches are invalidated by a tlbie[l] with RIC=2 or by a move to
PRTBL. The pgtbl0 cache is invalidated by a move to PID. The dTLB
and iTLB are cleared by a move to either PRTBL or PID.
Which of the two page table root pointers is used (pgtbl0 or pgtbl3)
depends on the MSB of the address being translated. Since the segment
checking ensures that address(63) = address(62), this is sufficient to
map quadrants 0 and 3.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Slbia (with IH=7) is used in the Linux kernel to flush the ERATs
(our iTLB/dTLB), so make it do that.
This moves the logic to work out whether to flush a single entry
or the whole TLB from dcache and icache into mmu. We now invalidate
all dTLB and iTLB entries when the AP (actual pagesize) field of
RB is non-zero on a tlbie[l], as well as when IS is non-zero.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a direct-mapped TLB to the icache, with 64 entries by default.
Execute1 now sends a "virt_mode" signal from MSR[IR] to fetch1 along
with redirects to indicate whether instruction addresses should be
translated through the TLB, and fetch1 sends that on to icache.
Similarly a "priv_mode" signal is sent to indicate the privilege
mode for instruction fetches. This means that changes to MSR[IR]
or MSR[PR] don't take effect until the next redirect, meaning an
isync, rfid, branch, etc.
The icache uses a hash of the effective address (i.e. next instruction
address) to index the TLB. The hash is an XOR of three fields of the
address; with a 64-entry TLB, the fields are bits 12--17, 18--23 and
24--29 of the address. TLB invalidations simply invalidate the
indexed TLB entry without checking the contents.
If the icache detects a TLB miss with virt_mode=1, it will send a
fetch_failed indication through fetch2 to decode1, which will turn it
into a special OP_FETCH_FAILED opcode with unit=LDST. That will get
sent down to loadstore1 which will currently just raise a Instruction
Storage Interrupt (0x400) exception.
One bit in the PTE obtained from the TLB is used to check whether an
instruction access is allowed -- the privilege bit (bit 3). If bit 3
is 1 and priv_mode=0, then a fetch_failed indication is sent down to
fetch2 and to decode1, which generates an OP_FETCH_FAILED. Any PTEs
with PTE bit 0 (EAA[3]) clear or bit 8 (R) clear should not be put
into the iTLB since such PTEs would not allow execution by any
context.
Tlbie operations get sent from mmu to icache over a new connection.
Unfortunately the privileged instruction tests are broken for now.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds the necessary machinery to the MMU for it to do radix page
table walks. The core elements are a shifter that can shift the
address right by between 0 and 47 bits, a mask generator that can
generate a mask of between 5 and 16 bits, a final mask generator,
and new states in the state machine.
(The final mask generator is used for transferring bits of the
original address into the resulting TLB entry when the leaf PTE
corresponds to a page size larger than 4kB.)
The hardware does not implement a partition table or a process table.
Software is expected to load the appropriate process table entry
into a new SPR called PGTBL0, SPR 720. The contents should be
formatted as described in Book III section 5.7.6.2 of the Power ISA
v3.0B. PGTBL0 is set to 0 on hard reset. At present, the top two bits
of the address (the quadrant) are ignored.
There is currently no caching of any step in the translation process
or of the final result, other than the entry created in the dTLB.
That entry is a 4k page entry even if the leaf PTE found in the walk
corresponds to a larger page size.
This implementation can handle almost any page table layout and any
page size. The RTS field (in PGTBL0) can have any value between 0
and 31, corresponding to a total address space size between 2^31
and 2^62 bytes. The RPDS field of PGTBL0 can be any value between
5 and 16, except that a value of 0 is taken to disable radix page
table walking (for use when one is using software loading of TLB
entries). The NLS field of the page directory entries can have any
value between 5 and 16. The minimum page size is 4kB, meaning that
the sum of RPDS and the NLS values of the PDEs found on the path to
a leaf PTE must be less than or equal to RTS + 31 - 12.
The PGTBL0 SPR is in the mmu module; thus this adds a path for
loadstore1 to read and write SPRs in mmu. This adds code in dcache
to service doubleword read requests from the MMU, as well as requests
to write dTLB entries.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a TLB to dcache, providing the ability to translate
addresses for loads and stores. No protection mechanism has been
implemented yet. The MSR_DR bit controls whether addresses are
translated through the TLB.
The TLB is a fixed-pagesize, set-associative cache. Currently
the page size is 4kB and the TLB is 2-way set associative with 64
entries per set.
This implements the tlbie instruction. RB bits 10 and 11 control
whether the whole TLB is invalidated (if either bit is 1) or just
a single entry corresponding to the effective page number in bits
12-63 of RB.
As an extension until we get a hardware page table walk, a tlbie
instruction with RB bits 9-11 set to 001 will load an entry into
the TLB. The TLB entry value is in RS in the format of a radix PTE.
Currently there is no proper handling of TLB misses. The load or
store will not be performed but no interrupt is generated.
In order to make timing at 100MHz on the Arty A7-100, we compare
the real address from each way of the TLB with the tag from each way
of the cache in parallel (requiring # TLB ways * # cache ways
comparators). Then the result is selected based on which way hit in
the TLB. That avoids a timing path going through the TLB EA
comparators, the multiplexer that selects the RA, and the cache tag
comparators.
The hack where addresses of the form 0xc------- are marked as
cache-inhibited is kept for now but restricted to real-mode accesses.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This arranges for some mfspr and mtspr to get sent to loadstore1
instead of being handled in execute1. In particular, DAR and DSISR
are handled this way. They are therefore "slow" SPRs.
While we're at it, fix the spelling of HEIR and remove mention of
DAR and DSISR from the comments in execute1.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Shawn Anastasio