We might want a non power of 2 amount of RAM in order to fit into an
FPGA, so create log2ceil and use it when calculating the number of
memory bits.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
The current version of micropython in tests/micropython.bin is ancient.
Bug #135 points out that more recent versions are much smaller and they
also handle restart when ctrl+D is pressed.
Save all three versions of the file (elf, bin and hex) in micropython/
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Shrink hello_world a bit (from 12kB to 8kB).
Include the built images
Add 0x10 and 0x100 entry points
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
This seems just to have been missed in commit f291efa266 ("decode1:
Mark ALU ops using carry as pipelined").
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a register in the middle of the countzero computation,
so that we now have two cycles to count leading or trailing zeroes
instead of just one. Execute1 now outputs a one-cycle stall signal
when it encounters a cntlz* or cnttz* instruction. With this,
the countzero path no longer fails timing on the Artix-7 at 100MHz.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This allows us to use the bypass at the input of execute1 for the
address and data operands for loadstore1.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This enables back-to-back execution of integer instructions where
the first instruction writes a GPR and the second reads the same
GPR. This is done with a set of multiplexers at the start of
execute1 which enable any of the three input operands to be taken
from the output of execute1 (i.e. r.e.write_data) rather than the
input from decode2 (i.e. e_in.read_data[123]).
This also requires changes to the hazard detection and handling.
Decode2 generates a signal indicating that the GPR being written
is available for bypass, which is true for instructions that are
executed in execute1 (rather than loadstore1/dcache). The
gpr_hazard module stores this "bypassable" bit, and if the same
GPR needs to be read by a subsequent instruction, it outputs a
"use_bypass" signal rather than generating a stall. The
use_bypass signal is then latched at the output of decode2 and
passed down to execute1 to control the input multiplexer.
At the moment there is no bypass on the inputs to loadstore1, but that
is OK because all load and store instructions are marked as
single-issue.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This implements logic in the logical entity to calculate the results
of the popcnt* and prty* instructions. We now have one insn_type_t
value for the 3 popcnt variants and one for the two prty variants,
using the length field of the decode_rom_t to distinguish between
them. The implementations in logical.vhdl using recursive
algorithms rather than the simple functions in ppc_fx_insns.vhdl.
This gives a saving of about 140 slice LUTs on the A7-100 and
improves timing slightly.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This handles OP_CMP like a subtraction; the main adder computes
~RA + RB + 1, and the condition codes are computed from the results.
A direct comparison of the two input operands is used to calculate the
EQ bit of the condition result. The LT and GT bits are computed from
the MSB of the subtraction result, the carry out from the subtraction,
and the MSBs of the operands. For a 32-bit comparison, the 32-bit
carry and bit 31 of the result and input operands are used; for a
64-bit comparison, the 64-bit carry and bit 63 of the operands and
result are used.
It turns out to be more convenient to use the 'signed' field of
the decode table to distinguish signed from unsigned comparisons,
rather than the insn_type. Therefore this uses OP_CMP for both
cmp and cmpl, which also has the benefit of reducing the number
of values in insn_type_t.
Doing this saves over 200 slice LUTs on the Arty A7-100 and improves
timing slightly as well.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This moves the sign extension done by the extsb, extsh and extsw
instructions back into execute1. This means that we no longer need
any data formatting in writeback for results coming from execute1,
so this modifies writeback so the data formatter inputs come
directly from the loadstore unit output. The condition code
updates for RC=1 form instructions are now done on the value from
execute1 rather than the output of the data formatter, which should
help timing.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
For multiply and divide operations, execute1 now records the
destination GPR number, RC and OE from the instruction, and the
XER value. This means that the multiply and divide units don't
need to record those values and then send them back to execute1.
This makes the interface to those units a bit simpler. They
simply report an overflow signal along with the result value, and
execute1 takes care of updating XER if necessary.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With this, the divider is a unit that execute1 sends operands to and
which sends its results back to execute1, which then send them to
writeback. Execute1 now sends a stall signal when it gets a divide
or modulus instruction until it gets a valid signal back from the
divider. Divide and modulus instructions are no longer marked as
single-issue.
The data formatting step that used to be done in decode2 for div
and mod instructions is now done in execute1. We also do the
absolute value operation in that same cycle instead of taking an
extra cycle inside the divider for signed operations with a
negative operand.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With this, the multiplier isn't a separate pipe that decode2 issues
instructions to, but rather is a unit that execute1 sends operands
to and which sends the result back to execute1, which then sends it
to writeback. Execute1 now sends a stall signal when it gets a
multiply instruction until it gets a valid signal back from the
multiplier.
This all means that we no longer need to mark the multiply
instructions as single-issue.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
It should never happen in practise, but ghdlsynth is complaining about
an inferred latch here. Fix it
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
From the architecture:
bits 0:31 and 35:43 are treated as reserved and return 0s when read
using mfxer
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Right now our test cases fold the SPRs into the GPRs. That makes
debugging fails more difficult than it needs to be, so print
out the CTR, LR and CR.
We still need to print the XER, but that is in two spots in microwatt
and will take some more work.
This also adds many instructions to the tests that we have added
lately including overflow instructions, CR logicals and mt/mfxer.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
I'm hitting an issue with the Fedora 31 version of GHDL that
appears to be fixed upstream:
control.vhdl:105:39:error: actual expression must be globally static
Add a signal to get rid of error.
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
This stores the most common SPRs in the register file.
This includes CTR and LR and a not yet final list of others.
The register file is set to 64 entries for now. Specific types
are defined that can represent a GPR index (gpr_index_t) or
a GPR/SPR index (gspr_index_t) along with conversion functions
between the two.
On order to deal with some forms of branch updating both LR and
CTR, we introduced a delayed update of LR after a branch link.
Note: We currently stall the pipeline on such a delayed branch,
but we could avoid stalling fetch in that specific case as we
know we have a branch delay. We could also limit that to the
specific case where we need to update both CTR and LR.
This allows us to make bcreg, mtspr and mfspr pipelined. decode1
will automatically force the single issue flag on mfspr/mtspr to
a "slow" SPR.
[paulus@ozlabs.org - fix direction of decode2.stall_in]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
We will want to store some SPRs in the register file using
a set of "extra" registers. This provides a function for
doing the translation along with some SPR definitions.
This isn't used yet
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
We were copying in XER[SO] for the dot-form instructions but not the
explicit compare instructions. Fix this.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The carry is currently internal to execute1. We don't handle any of
the other XER fields.
This creates type called "xer_common_t" that contains the commonly
used XER bits (CA, CA32, SO, OV, OV32).
The value is stored in the CR file (though it could be a separate
module). The rest of the bits will be implemented as a separate
SPR and the two parts reconciled in mfspr/mtspr in latter commits.
We always read XER in decode2 (there is little point not to)
and send it down all pipeline branches as it will be needed in
writeback for all type of instructions when CR0:SO needs to be
updated (such forms exist for all pipeline branches even if we don't
yet implement them).
To avoid having to track XER hazards, we forward it back in EX1. This
assumes that other pipeline branches that can modify it (mult and div)
are running single issue for now.
One additional hazard to beware of is an XER:SO modifying instruction
in EX1 followed immediately by a store conditional. Due to our writeback
latency, the store will go down the LSU with the previous XER value,
thus the stcx. will set CR0:SO using an obsolete SO value.
I doubt there exist any code relying on this behaviour being correct
but we should account for it regardless, possibly by ensuring that
stcx. remain single issue initially, or later by adding some minimal
tracking or moving the LSU into the same pipeline as execute.
Missing some obscure XER affecting instructions like addex or mcrxrx.
[paulus@ozlabs.org - fix CA32 and OV32 for OP_ADD, fix order of
arguments to set_ov]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
There is no reason not to that I can think of
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Anton Blanchard
Paul Mackerras